background image

SAFETY INSTRUCTIONS

WARNING! 

Read all instructions. Failure to follow all instructions listed 

below may result in electric shock, fire and/or serious injury.

SAVE THESE  INSTRUCTIONS
1) 

Work area

a) 

Keep work area clean and well lit.

Cluttered and dark areas invite accidents.

b) 

Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

c) 

Keep children and bystanders away while operating a power tool.

Distractions can

cause you to lose control.

2) Electrical safety
a) 

Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) 

Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or

grounded.

c) 

Do not expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

d) 

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) 

When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

3) 

Personal safety

a) 

Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication.

A moment of inattention while operating power tools may result

in serious personal injury.

PLEASE NOTE:

The generator supplied is 

NOT

suitable for providing power to any electronic products such as

computers, laptops or televisions etc.

If in doubt please refer to the specific product manual for advice on supply connection. If using for a

caravan, motor home or boat etc refer to the manufacturers manual regarding connection of a generator.

Do 

NOT

connect into a house ring main circuit.

Summary of Contents for SMK37GEN

























Reviews: