Summit Treestands Outlook SU82083 Manual Download Page 15

1. 

 It is required to have three (3) able adults to assist you in removing this ladder stand 

from the tree. Before climbing into the ladder stand, put on your FBFAHS on following 
the instructions and warnings for safe and proper use. 

Inspect all straps, ladder sections and the Stabilizer bar ensuring they are still properly 
attached and that they are not damaged.

With one person on each side of the ladder holding for stability, carefully climb up 
the ladder stand.  ALWAYS use 3-points of contact with the ladder as you climb. Upon 
arrival to foot platform area, immediately attach your FBFAHS to the tree. 

2.  

While secured to the tree with your FBFAHS, carefully disengage the upper ratchet 

strap from around the tree.  From this point until you are back at ground level, always 
ensure that two people are holding the ladder for stability.

3.  

Carefully disconnect your FBFAHS, and without shifting your weight around, slowly 

and carefully descend the ladder using 3-points of contact. 

4. 

Upon arrival to the ground, remove the Stabilizer bar from the tree and ladder 

section. Next, disengage the Criss-Cross straps and allow them to hang freely down 
under the foot platform as shown in 

figure 45

. Next, secure the Criss-Cross to ratchet 

straps connected to the ladder section below the third ladder rung and tighten until 
they are tight.  

See figure 46.

5.  

Using three (3) able adults, lift up on the ladder stand to pull the bottom ladder 

section out of the ground. Next, carefully walk the ladder stand down to the ground. 

DO NOT stand directly in the path of the ladder stand being lowered to the 
ground!! 

Inspect the ladder stand for any damage possibly resulting from removing this product 
from the tree. 

WARNING

!

NEVER REMOVE THE CRISS-CROSS STRAPS OR 
STABILIZER BAR UNTIL YOU ARE SAFELY BACK ON 
THE GROUND AND THE RATCHET STRAP AROUND 
THE TREE HAS BEEN REMOVED. NEVER CLIMB ANY 
LADDER STAND WITHOUT THE CRISS-CROSS STRAPS 
AND STABILIZER SECURED CORRECTLY!!

LOOSE CRISS-
CROSS STRAPS

45

WARNING

!

NEVER

 re-use ratchet straps that were left in the 

field for use. Call Summit Treestands to purchase 
replacement straps. Sunlight, animals, or tree growth 
could have affected the strap integrity which could 
cause the strap to fail, causing serious injury or death!

LADDER REMOVAL

46

PG 15

Summary of Contents for Outlook SU82083

































Reviews: