Sumitomo Drive Technologies PARAMAX SFC Operating Manual Download Page 3

PARAMAX SFC Operating Manual

e-mail: [email protected]
www.sumitomodriveeurope.com

Tel. +49 (0) 8136 66 0

Cyclostraße 92
85229 Markt Indersdorf

24

PX_SFC_DEU_ENG_11_09_991131

1. General Information

Please always follow the safety instructions indicated below in this document.

Danger due to Electricity

Incorrect use of the machine can lead to physical injury, serious injury and/or life-threatening situa-
tions.

Danger

Incorrect use of the machine can lead to physical injury, serious injury and/or life-threatening situations.

Dangerous Situation

Slight injuries may result.

Possible Damage Situation

Damage to the drive or the environment may result.

Helpful Information

Disposal

Please follow the applicable regulations.

 Important Information about Explosion Protection

Information applying to PARAMAX SFC Gear Unit

2. Safety Information

Before working with the machine (assembly, operation, maintenance, inspection, etc.), read through 
these operating instructions carefully, so that you understand exactly how to operate the PARAMAX 
SFC gear unit, and know the safety regulations to be followed and warning information to be observed. 
Keep this manual near the machine, so that it can be referred to at any time when necessary.

Transport, installation, lubrication, operation, maintenance, and inspection should be carried out only 
by properly trained technical personnel; otherwise there is a risk of injuries, or damage to the machine.
Never attempt to grasp moving parts, and keep foreign objects away from such parts; otherwise there is 
a risk of injuries, or damage to the machine.
The system should be used only for its intended purpose; otherwise there is a risk of injuries, or damage 
to the machine.

Replacement Parts

Use only original replacement parts. All warranties are void if non-approved replacement parts are used. 

SIT S.A.     |      Tfno. 943 457200     |     [email protected]     |      www.sitsa.es

SIU 8320-00

            Instrucciones de instalación y mantenimiento Reductores PARAMAX SFC para Torres de Refrigeración

20/03/2018

Summary of Contents for PARAMAX SFC






















Reviews: