manualshive.com logo in svg

SULO MGB 1100 RD, Assembly Instructions And Spare Parts List

Share
Download
SULO MGB 1100 RD Assembly Instructions And Spare Parts List Download Page 17

 

 
 

Assembly Instructions MGB 1100 RD B 

17/22

 

 

Insert one end of each rod (Pos. 64) into the respective drill hole (see detail “A”) of 

the bearings in the lid and insert the other end into the guide shaft. Make sure that 

both rods are positioned properly inside the designated indentations in the ribs 

beside each guide shaft (see detail “B”) before mounting the hand guard (Pos. 65). 

Then fasten the rubber hand guard to the lid with screws (Pos. 66). Start of with the 

middle screw which centres the hand guard. The tightening torque must not be more 

than 2 Nm. 

Check the function of guide shafts and rods by pushing both buttons. 

 

 

2.1.2  Gravity boxes inside the body 

For assembly, place the gravity box outside the body (Pos. 48), slide the catch 

through the designated slot and fasten the box from inside with the provided screws. 

The tightening torque must not be more than 1.7 Nm. 

 

 
 

 

 

48 

Summary of Contents for MGB 1100 RD























Reviews:

No comments

Brands by name

Popular brands

Load more brands