background image

Page 8

Icemaker Information

6-8

#7005333 - Revision C - September, 2010

Built-In (BI) Series

Built-In (BI) Series

Figure 6-11.  End of Ice Making Cycle

APPROXIMATE POSITION

OF ICE EJECTOR AND 

ICE LEVEL ARM 

DURING OPERATION

115 VOLTS

60 CYCLES

SHUT-OFF SWITCH

THERMOSTAT

MOLD HEATER

WATER

SOLENOID

SOLENOID SWITCH

MOTOR

HOLDING SWITCH

NO

NC

C

NC

NC

NO

NO

C

C

TCO

ICE MOLD

ICE BUCKET

WATER

ICE

ICE

End of Ice making Cycle 

 (See Figure 6-11)

• The  water valve solenoid switch is tripped by the

timing cam back to “normally open” ending the
water fill.

• The timing cam trips the holding switch to “normally

close,” which ends the second revolution.

• The thermostat is still open, so it does not start the

drive motor.

• If the shut-off arm has come to rest on top of the

ice in the storage bin (as illustrated), the shut-off
switch remains in the “normally closed” position.
This interrupts power from reaching the thermostat,
until sufficient ice has been removed from the stor-
age bin allowing the shut-off arm to lower.

NOTE: 

To allow ice to freeze fully and reduce effects of

low water pressure, the electronic control system dis-
ables the icemaker system for 45 minutes after each ice
harvest.

Figure 6-12.  Stopping Icemaker

Arm DOWN,

Icemaker will Operate

Arm UP,

Icemaker will Stop

MANUALLY STOPPING ICE PRODUCTION

Ice production can be manually stopped two ways:

1.

Press the “ICE MAKER” key on the control panel so
that the ice cube icon is not displayed on the LCD.

2.

Position the ice-level/shut-off arm in the up/OFF
position 

(See Figure 6-12)

.

Summary of Contents for BI Series











Reviews: