background image

3

T H A N K YO U

Congratulations on the purchase of your
Sub-Zero ice machine. It produces the same
high quality clear ice that you would expect
from Sub-Zero.

The importance of the installation of the ice
machine cannot be overemphasized. Installa-
tion should be done by a qualified installer.

Before you begin the installation process,
it is recommended that you read the entire
installation instructions. There are key details
that you should take special care to observe
during the installation. By reading these
instructions carefully, you will make the
installation process easier, problem-free and,
most importantly, safe.

Any questions or problems about the
installation should be directed to your
Sub-Zero dealer or Sub-Zero customer service
at 800-222-7820. You can also visit our website
at subzero.com.

The Sub-Zero ice machine is protected by a
warranty that is one of the finest in the
industry. Take a moment to read the warranty
statement on page 31 and refer to it should
service become necessary.

The operation information in this book will
answer most of your questions about the
features, operation and maintenance of your
ice machine. If you have questions that are not
addressed here, call Sub-Zero customer
service at 800-222-7820 or visit our website
at subzero.com.

S U B - Z E R O

I C E M A C H I N E

I N S T A L L A T I O N A N D O P E R A T I O N

IMPORTANT NOTE:

Your Sub-Zero ice

machine is designed and manufactured with
the highest regard for safety and perform-
ance. It meets or exceeds the standards of UL
and CUL. Sub-Zero assumes no liability or
responsibility of any kind for products manu-
factured by Sub-Zero that have been altered
in any way, including the use of any parts
and/or other components not specifically
approved by Sub-Zero. Sub-Zero reserves the
right to make design changes and/or
improvements at any time. Specifications and
designs are subject to change without notice.

C O N T A C T
I N F O R M A T I O N

Sub-Zero
customer service:
800-222-7820

Website:
subzero.com

Do not operate equipment that has been
misused, abused, neglected, damaged, or
altered/modified from that of original
manufactured specifications.

P R O D U C T R E G I S T R AT I O N

C A R D

The packet containing this manual also
includes warranty information. Warranty
coverage begins the day your new ice machine
is installed.

IMPORTANT NOTE:

Complete and mail the

product registration card as soon as possible
to validate the installation date. If you do not
return your product registration card, Sub-Zero
will use the date of sale to the Sub-Zero dealer
as the first day of warranty coverage for your
new ice machine.

Summary of Contents for UC-15I

































Reviews: