background image

19

S U B - Z E R O

I C E M A C H I N E

O P E R A T I O N

CLEAN Button (Green)

Pressing the

CLEAN

button will initiate a clean

cycle and de-activate the

ICE

light. The

CLEAN

light will flash during the clean cycle to
indicate the proper time to add ice machine
cleaner or sanitizer.

Replace Filter (Red)

When the ice machine completes 8000
freeze/harvest cycles the light will illuminate to
indicate the filter needs replacement. Depress-
ing the

CLEAN

button for 6 seconds will reset

the counter and light.

C O N T R O L

P A N E L

F U N C T I O N S

POWER Button (Green)

Pressing the

POWER

button once will activate

the ice machine and green

POWER

light.

Pressing the

POWER

button a second time will

de-activate the ice machine.

Automatic Ice Making Light (Blue)

The

ICE

light is illuminated when the ice

machine is in the ice making position. The light
is off when the ice machine is in the clean
cycle.

Delay Start

Pressing the

DELAY

button will initiate a delay

cycle. The ice machine will not run until the
delay time expires.

Pressing the button once will illuminate the

2

hour light and initiate a two hour delay

period.

Pressing the button a second time will illu-
minate the

4

hour light and initiate a four

hour delay period.

Pressing the button a third time will illumi-
nate the

8

hour light and initiate an eight

hour delay period.

Pressing the button a fourth time will cancel
the delay cycle.

I C E M A C H I N E C O N T R O L P A N E L

Summary of Contents for UC-15I

































Reviews: