Sub-Zero 700TF Planning Information Download Page 3

Planning Information

Model 700TF(I)

Dimensions in parentheses are in
millimeters unless otherwise specified.

3

M O D E L   O P T I O N S

All Freezer

700TF

All Freezer
with Automatic Ice Maker

700TFI

P A N E L   O P T I O N S

Integrated (custom panels)

Classic Stainless Steel Finish

/S

Platinum Stainless Steel Finish

/P

Carbon Stainless Steel Finish

/B

Stainless steel door and drawer front
panels are ordered and shipped as sales
accessories and include tubular handles.

A C C E S S O R I E S

Tubular handles in classic,
platinum and carbon stainless
steel

Dual installation heater kit
(TTDUAL or BBDUAL)

Accessories are available through your
Sub-Zero dealer. To obtain local dealer
information, visit the Locator section of
our website, subzero.com.

S P E C I F I C A T I O N S

Model 700TF(I)

All Freezer

Overall Width

27" (686)

Overall Height

80" (2032)

Overall Depth

24" (610)

Freezer Capacity

15.3 cu ft (433 L)

Minimum Height (levelers in)

79

1

/

2

" (2019)

Door Clearance

25

1

/

2

" (648)

Drawer Clearance

19

1

/

2

" (495)

Electrical Requirements

115 V AC, 60 Hz, 15 amp circuit

Plumbing Requirements

1

/

4

" copper line

Water Supply

20–100 psi

Annual Energy Usage

652 kWh / $ 55

(based on 8.29 cents per kilowatt hour)

Shipping Weight

360 lbs (163 kg)

Special Note

Door and drawer panels and handles are 

available in three stainless steel finishes

Specifications are subject to change without notice.

Summary of Contents for 700TF
















Reviews: