Sub-Zero 400-2 Series Installation Information Download

Page: 8 / 11

Wine Storage

(400-

)

Series

Installation Information

2-9

#3758410 - Revision C - May, 2014

Figure 2-23. Overlay Door Panel Removal

Door Assy

Poly
Tape

Panel
Mounting
Screws

Overlay Panel

SS Handle Shown (Handle may vary)

Figure 2-22. Poly Tape Removal

Poly Tape

Door Gasket

Door Frame

Overlay Door Panel Removal and Installation (424-2)

Overlay panels are attached to the door using screws
passing through the door frame from the rear, into the
panel. The handle may also be attached through the
door frame or just through the panel.

To Remove an Overlay Panel:

Open door.

Remove Poly-tape under gasket which covers
panel mounting screw holes (See Figure 2-22).

NOTE:

Do not discard tape. It must be reapplied

when panel is reinstalled.

Extract panel mounting screws, and possibly handle
mounting screws. (See Figure 2-23)

Pull overlay panel from door.

NOTE:

To install overlay panel, reverse steps above.

Summary of Contents for 400-2 Series












Search results

Summary of Contents for 400-2 Series

Reviews:

Related manuals for 400-2 Series

Brands by name

Popular brands

Sub-Zero 400-2 Series, Installation Information

Search results

Summary of Contents for 400-2 Series

Reviews:

Related manuals for 400-2 Series

Brands by name

Popular brands