4
CITYBEAM
art.
0203
CITYBEAM
art.
0203
®
SN
SN
230
V
; 14
A -
60
Hz
AC
230
V
; 14A
- 60
Hz
AC
QC
QC
Disconn
ect
the
unit
from
powe
r be
fore
se
rvicing
Keep
at least
a distance
of 0.5mt
between
the
apparatus
and
inflammabl
e su
rface
nearb
y
1
8
0
0
W
1800W
CITYBEAM
art.
0203
CITYBEAM
art.
0203
®
SN
SN
230
V
; 14A
- 60
Hz
AC
230
V
; 14A
- 60
Hz
AC
QC
QC
Disconnect
the
unit
from
power
before
servicing
Keep
at
least
a distance
of
0.5mt
between
the
apparatus
and
inflammable
surface
nearby
1
8
0
0
W
1800W
BEFORE USING
Read all cautions and warnings to page 1 prior to install this equipment. Particularly, read the follow:
1) Disconnect power before lamp’s replacement or servicing (service personnel)
2) Do not open the lamp cover for 300 seconds after switching off
3) Wear gloves and goggles to re-lamping or to work inside the unit (service personnel)
Before connecting the equipment to the power system: make sure that the mains voltage and frequency correspond to rated
values.
• The CityColor can be equipped for a mains voltage 230Vac, 50Hz.
on request: 200V/50Hz; 208V/60Hz; 230V/60Hz; 240V/50Hz
For a power supply of 100V-120V it is necessary to use one auto transformer with the following features:
• Output voltage 230V
• Output current 15A (for art. 0002)
• Output current 20A (for art. 0003)
The power supply cords construction is shown in pict.1. For connection to the mains supply proceed as pict.1.
The equipment must be connected to branch circuit having a circuit-breacker In=16A • Id=0.03A (230VAC) (art. 0002) or
In=32A • Id=0.03A (230VAC) (art.0003)
a) Do not install the spot close to the heat sources. Observe minimum distance between the spots of 1.5 meters. Do not lay the
connection cable on the spot when it is warm.
b) This unit must be positioned as to allow its ventilation. Be careful not to acclude the in-out ventilating grilles.
c) The unit must be positioned at least 50cm. from walls or other flammable surfaces.
d) Observe minimum distance to lighted objects of 5 meters.
External surface temperature Ta 35°C:
• After 5 minutes work; Tc=75°C.
• Once the thermic balance has been obtained; Tc=100°C.
4) The protection screens, the lenses, or the ultraviolet filters must be replaced if they are visibly damaged and their effectiveness
has been reduced, for example, by cracks or deep scratches.
5) The lamp must be replaced if it has been damaged or thermally deformed.
6) Clean regularly the in-out ventilating grilles.
7) Do not handle the spot by taking it by the head, but always by using the special handles.
WARNING
!
IP 67
pict.1
The equipment must be earthed.
IP 54 rate: the equipment must be installed on the horizontal plane.
INPUT CONNECTOR
FOR 1800W
INPUT CONNECTOR
FOR 2500W HIGH POWER
IP 67
3 PIN CONNECTOR FOR POWER INPUT
N = NEUTRAL
L = LIVE
= GROUND
CONDUCTOR SIZES (length < 20mt.)
MAINS VOLTAGE
CROSS SELECTIONAL AREAS
230V
3X1,5 mm
2
(minimum)
CIRCUIT BREAKER
MAINS VOLTAGE
In
Id
230V
32A
0,03A
