STUDIO DUE CITYCOLOR 2500 IP54 Manual Download Page 3

3

YOUR REFERENCE

Always remember to give the serial number and to specify the model any time you address the seller for information or assistan-
ce.

BASIC KIT

The basic kit of the CityColor flood projector consist of:

•Projector
•User’s manual
•Power connector
•Studio Due warranty

Available on request:
•art. 9801/a: barndoor to define illuminated surface
•art. 0003/a: anti glare
•art. 0002/a: XLR 3 pin male IP54 connectors
•art. 0002/b: XLR 3 pin female IP54 connectors
•Lamp

TECHNICAL FEATURES

•LAMPS
 MHN/SA 1800W PHILIPS (art. 9801 - 0002)
Color temperature: 5.600°K
Lamp life: 2.500 hours
Luminous flux 180.000 lm
 
•OPTIC COLOR SYSTEM
Full CYM color mixing, unlimited variety of colours and shades. High resolution stepper motors.
S dimmer. The color changer can be drived with 4 different speeds or in real time. 

•BEAM ANGLE: (50% intensity) 50°x52°

•CONTROL INPUT
Standard interface: RS-485; opto-couplet input.
Protocol: USITT DMX 512

•SETUP AND CONFIGURATION
On the control panel with menu and buttons

•AUTOMODE
Stand-alone control: auto mode function master/slave (synchro mode) with 27 programs
 

 

•IP RATE: IP 54 (art. 0002 - 0003)

•POWER SUPPLY: (art. 0002) magnetic bal last 
Rated voltage: 230V/50Hz
On request:     200V/50Hz; 208V/60Hz; 230V/60Hz; 240V/50Hz
Rated current: 10A
Rated power: 2000W 

•POWER SUPPLY: (art. 0003) magnetic ballast
Rated voltage: 230V/50Hz
On request:     200V/50Hz; 208V/60Hz; 230V/60Hz; 240V/50Hz 
Rated current: 14A
Rated power: 3000W

•POWER FACTOR CORRECTOR: built-in cos Ø 0.9

•DMX CHANNELS
ch1 = motors speed
ch2 = cyan
ch3 = yellow
ch4 = magenta

•DIMENSIONS (wxdxh)
mm 780x560x740

•WEIGHT
art. 0002:   56 kgs. net
art. 0003:   69 kgs. net

HTI/DE 2500W OSRAM • MSA/DE 2500W PHILIPS (art. 0003)
Color temperature 6.000°K
Lamp life 2.000 hours
Luminous flux 260.000 lm

ch5 = dimmer
ch6 = basic rainbow 
ch7 = remote reset/lamp off

Summary of Contents for CITYCOLOR 2500 IP54

















Reviews: