manualshive.com logo in svg

Stuart Turner Showermate 1.5 bar Single, Installation Instructions Manual

Share
Download
Stuart Turner Showermate 1.5 bar Single Installation Instructions Manual Download Page 20

Issue No: 1908/1-02

Part No. 18956

Stuart Turner Ltd, Henley-on-Thames, Oxfordshire RG9 2AD ENGLAND

Tel:   +44 (0) 1491 572655,      Fax:   +44 (0) 1491 573704

email:   [email protected]    web:  www.stuart-turner.co.uk

V.A.T. REG. No. 199 0987 92. Registered in England No. 88368. Registered Office: Market Place, Henley-on-Thames

DECLARATION OF CONFORMITY

98/37/EC

BS EN ISO 12100-1, BS EN ISO 12100-2, BS EN 809

2006/95/EC

BS EN 60335-1, BS EN 60335-2-41, EN 50366

89/336/EEC

BS EN 55014-1, BS EN 55014-2, BS EN 55022, BS EN 61000-3-2,  BS EN 61000-3-3, 

BS EN 61000-4-2,  BS EN 61000-4-3, BS EN 61000-4-4, BS EN 61000-4-5, BS EN 61000-4-6, 

BS EN 61000-4-11 

IT IS HEREBY CERTIFIED THAT THE STUART ELECTRIC MOTOR DRIVEN PUMP AS 
SERIAL NUMBER BELOW, COMPLIES WITH THE ESSENTIAL REQUIREMENTS OF THE 
ABOVE E.E.C. DIRECTIVES.

RESPONSIBLE PERSON
AND MANUFACTURER

STUART TURNER LIMITED
HENLEY-ON-THAMES, OXFORDSHIRE
RG9 2AD  ENGLAND.

Signed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Quality Manager

Stuart Turner are an approved company to BS EN ISO 9001:2000

Summary of Contents for Showermate 1.5 bar Single






















Reviews:

No comments

Brands by name

Popular brands

Load more brands