background image

- 17 -

10  YOUR WARRANTY

Congratulations on purchasing a Stuart Turner Mainsboost system. 

We are confident this product will give you many years of trouble free service as all 

our products are manufactured to the very highest standard. 

Mainsboost vessels are warrantied for five years, fittings including the 

Mainsboost Monobloc and other ULK components are warrantied for 2 years.

Within the warranty period we will repair, free of charge, any defects in the  

Mainsboost resulting from faults in material or workmanship, repairing or 

exchanging the part affected or whole unit as we may reasonably decide. 

Not covered by this warranty: Damage arising from incorrect installation, improper 

use, unauthorised repair, normal wear and tear and defects which have a negligible 

effect on the value or operation of the unit. 

Reasonable evidence must be supplied that the product has been purchased 

within the warranty term prior to the date of claim (such as proof of purchase or the 

product serial number). 

This warranty is in addition to your statutory rights as a consumer.  If you are in any 

doubt as to these rights, please contact your local Trading Standards Department. 

In the event of a claim please telephone 

‘TechAssist’

 customer support.

+44 (0) 800 31 969 80

You should obtain appropriate insurance cover for any loss or damage which is not 

covered by Stuart Turner Ltd in this provision.

Please record here for your reference.

TYPE NO.

SERIAL NO.

DATE PURCHASED

Summary of Contents for Mainsboost MB 100CV





















Reviews: