Stryker SYSTEM G 4103-082-131, Instructions For Use Manual, Page: 4 / 148

4 www.stryker.com
EN 7305-001-700 Rev-A
For Use With
This section identifies components intended to be used
with the equipment to obtain a safe combination.
WARNINGS:
▪ Use only Stryker-approved equipment, unless
otherwise specified.
▪ Use of unapproved electrical equipment may result
in increased electromagnetic emissions or decreased
electromagnetic immunity of the system.
NOTE: For a complete list of components or ordering
information, contact your Stryker sales representative or
call Stryker customer service. See the
Contact Information
section. Outside the US, contact your nearest Stryker
subsidiary.
Power and Care Components
Description REF
STRYKER SYSTEM G Transfer
Shield 7304-120-000
STRYKER SYSTEM G Power
Module 7309-120-000
STRYKER SYSTEM G Charger,
2-Bay 7310-120-000
STRYKER SYSTEM G Sterilization
Cases 7302-120-000
7302-130-000
Attachments and Cutting and
Fixation Tools
WARNING: All cutting and fixation tools are intended
for single use only.
Wire and Pin Collets
NOTE: Wire and pin collets REF 4103-063-000, 4103-
126-000S3, and 4103-126-000 are not compatible with
STRYKER SYSTEM G.
Attachment REF Tools
STRYKER
SYSTEM G
Wire Collet 7307-001-000 Kirschner wires and
Steinmann pins
from 0.7 to 1.8 mm
in diameter
STRYKER
SYSTEM G Pin
Collet, Small 7307-002-000 Kirschner wires and
Steinmann pins
from 2.0 to 3.2 mm
in diameter
STRYKER
SYSTEM G Pin
Collet, Large 7307-003-000 Kirschner wires and
Steinmann pins
from 3.0 to 4.2 mm
in diameter
Keyed Chucks
NOTE: Each chuck is supplied with a chuck key (REF
1331-001-009)
Attachment REF Tools
1:1 1/4 inch
(6.4 mm) Keyed
Chuck 4103-131-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
High Torque 1/4
inch (6.35 mm)
Drill with Chuck
2:1 with Key 4103-180-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
3.25:1 1/4 inch
(6.4 mm) Keyed
Chuck 4103-231-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Keyless Chucks
NOTE:
The Keyless Chuck Adaptor (REF 4103-082-131) is
intended for use with standard Trinkle attachments.
Attachment REF Tools
Keyless Chuck
Adaptor 4103-082-131 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Keyless Drill
Attachment 4103-133-000 Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Drill Attachments
Attachment REF Tools
1:1 AO Small
Drill 4103-110-000 Drill bits, taps,
automatic
screwdrivers, and
tools with AO snap-
lock shanks
1:1 Hudson 4103-113-000 Drill bits, reamers,
taps, automatic
screwdrivers, and
tools with Hudson
fittings
1:1 Hudson/
Modified Trinkle 4103-135-000 Drill bits, reamers,
automatic
screwdrivers, and
tools with Hudson
or modified Trinkle
fittings
1:1 Trinkle 4103-160-000 Drill bits, reamers,
automatic
screwdrivers, and
tools with standard
Trinkle fittings