Stryker LIFEPAK 20 Inspection Procedure Download Page 9 | Manualshive

Page: 9 / 61

background image

LIFEPAK

®

20

Performance Inspection Procedure (PIP)

3201896-000_B

©2019 Stryker

--- CONTENTS ---

Page 9 of 61

PIP - Exterior Physical Inspection/Cleaning Paddles

To perform an exterior physical inspection:

1. Inspect the LIFEPAK 20 exterior for the following: Damage, excessive wear, improper mechanical function, and damaged

connectors.

2. Pick up and turn over the device and listen for loose or rattling hardware. Locate any loose or rattling hardware, and then tighten or

replace it.

3.  Inspect the rubber feet on the underside of the lower enclosure. Reinstall or replace rubber feet as necessary.
4.  Inspect the Therapy, ECG, SpO2 (if equipped), DB-9, DB-15, AED door, and IrDA connectors for damage and or cracks.
5.  Inspect the keypads and overlays for damage, cracks, and separations.
6.  Check all other accessory cables, Paddles, ECG, SpO2 sensors, and related items for expiration dates, general condition, and

suitability for use.

7. Inspect carrying strap and mounts (if the device is equipped with them).

To perform Cleaning Paddles:

1.  Disconnect the adult paddle plate from the paddle assembly.
2.  Clean the spring contact of the adult paddle with alcohol.
3.  Clean the pediatric electrode surface with alcohol.
4.  Reattach the adult paddle plate to the paddle assembly.

«
...
7
8
9
10
11
...
»

Summary of Contents for LIFEPAK 20






























































Reviews:

No comments

Related manuals for LIFEPAK 20

Pressure Governor

Brand: Waterous Pages: 53

Brand: Landi Renzo Pages: 16

Brand: IBM Pages: 163

Brand: Nectar Pages: 46

Brand: Neauvia Pages: 17

Brand: Safety 1st Pages: 4

Brand: Safety Engineering Pages: 5

Brand: Feniex Pages: 5

Brand: Delfield Pages: 24

Brand: American DJ Pages: 8

Brand: COURANT Pages: 2

Brand: laerdal Pages: 64

Nursing Kelly VitalSlim

Brand: laerdal Pages: 100

Thermal Cycler Dice Real Time System III

Brand: Takara Bio Pages: 54

Brand: OttLite Pages: 2

Brand: Festo Pages: 42

MONTESOL Nasal Douche

Brand: Pari Pages: 46

Brand: Hamron Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands