manualshive.com logo in svg

Stryker Medical RUGGED 6080 MX-PRO, Operation & Maintenance Manual

Share
Download
Stryker Medical RUGGED 6080 MX-PRO Operation & Maintenance Manual Download Page 28

Cleaning

25

Hand wash all surfaces of the cot with warm water and mild detergent.  Dry thoroughly.  DO NOT STEAM
CLEAN, PRESSURE WASH, HOSE OFF OR ULTRASONICALLY CLEAN.  Using these methods of cleaning
is not recommended and may void this product’s warranty.
Clean Velcro AFTER EACH USE.  Saturate Velcro with disinfectant and allow disinfectant to evaporate.  (Ap-
propriate disinfectant for nylon Velcro should be determined by the hospital.)

In general, when used in those concentrations recommended by the manufacturer, either phenolic type or
quaternary type disinfectants can be used.  Iodophor type disinfectants are not recommended for use be-
cause staining may result.  The following products have been tested and have been found not to have a harm-
ful effect WHEN USED IN ACCORDANCE WITH MANUFACTURERS RECOMMENDED DILUTION.*

 

TRADE NAME

 

DISINFECTANT

TYPE

MANUFACTURER

*MANUFACTURER’S

RECOMMENDED

DILUTION

A33

Quaternary

Airwick (Professional Products Division)

2 ounces/gallon

A33 (dry)

Quaternary

Airwick (Professional Products Division)

1/2 ounce/gallon

Beaucoup

Phenolic

Huntington Laboratories

1 ounce/gallon

Blue Chip

Quaternary

S.C. Johnson

2 ounces/gallon

Elimstaph

Quaternary

Walter G. Legge

1 ounce/gallon

Franklin
Phenomysan F2500

Phenolic

Purex Corporation

1 1/4 ounce/gallon

Franklin Sentinel

Quaternary

Purex Corporation

2 ounces/gallon

Galahad

Phenolic

Puritan Churchill Chemical Company

1 ounce/gallon

Hi–Tor

Quaternary

Huntington Laboratories

1/2 ounce/gallon

LPH

Phenolic

Vestal Laboratories

1/2 ounce/gallon

Matar

Phenolic

Huntington Laboratories

1/2 ounce/gallon

Omega

Quaternary

Airwick (Professional Products Division)

1/2 ounce/gallon

Quanto

Quaternary

Huntington Laboratories

1 ounce/gallon

Sanikleen

Quaternary

West Chemical Products

2 ounces/ gallon

Sanimaster II

Quaternary

Service Master

1 ounce/gallon

Vesphene

Phenolic

Vestal Laboratories

1 1/4 ounce/ gallon

Quaternary Germicidal Disinfectants, used as directed, and/or Chlorine Bleach products, typically 5.25% So-
dium Hypochlorite in dilutions ranging between 1 part bleach to 100 parts water, and 2 parts bleach
to 100 parts water are not considered mild detergents.  These products are corrosive in nature and may
cause damage to your cot if used improperly.  If these types of products are used to clean Stryker patient
handling equipment, measures must be taken to insure the cots are rinsed with clean water and thoroughly
dried following cleaning. Failure to properly rinse and dry the cots will leave a corrosive residue on the surface
of the cots, possibly causing premature corrosion of critical components.

NOTE
Failure to follow the above directions when using these types of cleaners may void this product’s warranty.

REMOVAL OF IODINE COMPOUNDS

1. Use a solution of 1–2 tablespoons Sodium Thiosulfate in a pint of warm water to clean the stained area.

Clean as soon as possible after staining occurs.  If stains are not immediately removed, allow solution to
soak or stand on the surface.  Rinse surfaces which have been exposed to the solution in clear water be-
fore returning unit to service.

WARNING
Failure to properly clean or dispose of contaminated mattress or cot components will increase the risk of expo-
sure to bloodborne pathogens and may cause injury to the patient or the operator.

Summary of Contents for RUGGED 6080 MX-PRO










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands