background image

13 

1. Shelf Assembly Removal 

 



Remove glass shelves 



For lighted shelving, unplug the light cord. 



Lift light shelf straight up to separate from 
brackets. 



Remove rear shelf support 



Remove brackets. Note it may be necessary   
to remove the nylon shipping bracket retainer.  
Pliers will be required to accomplish this task. 

 

2. Light Fixtures  

 

Removal of lamp: 



Rotate lamp (1/4-turn) either direction to        
disengage (upper or lower) pins/contacts from 
lamp mounting sockets.   



Remove bulb by applying even pressure from 
the back side at the bulb ends and pulling the 
remaining contact from the sockets.

 

 

Installation of lamp: 



Align pins with slot. 



Insert pins into socket by rotating the bulb      
1/4-turn to secure either the (upper or lower) 
pinned contacts into the sockets. 



Rotate the remaining bulb contacts (1/4 turn) 
into the remaining lamp-mounting socket      
contacts.  



See illustration below. 

MAINTENANCE FUNDAMENTALS - SHELF ASSEMBLY / LIGHT FIXTURES 

Lamp Pins

 

Light  Socket

 

Light Fixture

 

Sample light fixture shown above.  To remove 

lamp, simply rotate lamp clockwise and out.      

To replace, place one set of pins into slots and 

rotate second set of pins into slots. 

Shelf Bracket 

Rear Shelf Support 

Glass 

Shelving 

Light 
Fixture 

Shelf Bracket 

 

Bracket 

Retainers

 

Summary of Contents for Harmony HMO3936R




































Reviews: