background image

START-UP AND OPERATION  

1. Caster Locking Operation (if option chosen) 

 



To lock casters push down on lever, to unlock pull 
up the lever all the way. 



See illustration at below right for view of Locking 
Casters. 

 
2. Electrical Access and Connections

 

 

Rear Wireway, if used -  Remove screws from rear 
wireway cover to access electrical leads. 
 



Wiring may run case to case through cut-outs in 
base. 



Knockout is provided in bottom of wire-way for 
stub-up connection. 



Separate leads for lights that are labeled           
accordingly. 



Standard 120 volt, single phase connections is 
required and should be performed by a certified 
electrician. 

 
Ballast Box, if used - Remove screws from ballast box 
cover,  rear panel, and ballast box inner support. 
Knockouts are located on side of box for making    
electrical connections. 
 

3. Merchandiser Start-Up 

 

Turn on the lights. All of the lights should come on at 
the same time.  



First time lighting may require a short warm up  
period for the bulbs.  



Slightly dim or a flickering of new bulbs is normal.  



If lights do not turn on, check all of the raceway 
plugs.  



The lighting is wired in series so 

all lights must 

be plugged in or receptacles capped 

in order 

for the case to light. 

Ballast 

Electrical Cutout 

Wire-way Cover 

Ballast 

Ballast box

 

OFF

 

ON

 

Rocker Switch

 

Cap

 

Plug

 

Receptacle

 

Locked 

Unlocked 

 

 

Summary of Contents for ENCORE Series


















Reviews: