background image

 

 

 

10 

TECHNICAL PASSPORT, INSTALLATION AND MAINTENANCE MANUAL

 

 

8

 

ENVIRONEMNTAL PROTECTION 

8.1

 

Packaging disposal  

 

The boiler is delivered in a package. 

 

Wooden and paper packaging can be burned in boiler of solid fuel, if user has one, or disposed 
according to requirements of environmental protection. 

Replaced parts of heating system need to be forwarded to respective waste management company. 

 

8.2

 

Boiler utilization 

 

 

At the end of the boiler's service life, it is dismantled and returned for recycling. 

 

9

 

WARRANTY 

9.1

 

Warranty conditions 

 

1. 

If the user follows the instructions of installation, operation and maintenances, indicated in user 
manual, the distributor provides a warranty according to conditions listed below: 
• Boilers are given a 24-month warranty from the day of purchase, but not longer than 36 months 
from the day of manufacture. 

2

The warranty does not cover consumables such as padding, sealing gaskets, fireclay  inserts, plugs, 

sockets, fuses. The warranty does not apply if mechanical, thermal or chemical damage to the device is 

due to improper actions or omissions. 

 

3

Regulation of boiler combustion parameters, maintenance (cleaning), replacement of parts of the set 

service life (fuses, electric heaters, sealing gaskets) are not included in the scope of warranty work and 

the responsibility for them lies with the user. 

4. 

The distributor is only liable under the terms of the warranty if the defect is due to the causes of the 

product sold or if a defect occurred in a physical device. The warranty does not cover any interruptions 

or failures of the boiler due to poor quality fuel or non-compliance with installation instructions or 

legislation, improperly selected equipment, improper chimney or poor draft in the chimney. 

5. 

Arbitrary changes to the boiler design, non-compliance with the installation, operation and maintenance 

instructions in the manual, failure to operate the boiler or conduct mandatory inspection, or failure to 

pay the seller shall suspend or terminate the warranty. The user covers maintenance staff fees if: 

 

• Maintenance personnel are called to perform non-warranty work. 

• Repairs are needed due to the fault of the user or an independent distributor 

• It is not possible to repair the fault for reasons beyond the control of the maintenance personnel  

(e.g. no fuel, no draft in the chimney, leaking system, improperly installed boiler). 

 

 

 

Summary of Contents for Pellet















Reviews: