Striking energy G3 1000 G Instructions Manual Download Page 3

Safety instructions  

Page 

!

 of 

!

                                   www.striking.co.za

 

           

[email protected]

 

3

12

• The appliances must be installed by a qualified electrician according to the legal 

regulations as published. 

• The heater must always be earthed. 
• DO NOT cover the heater with anything. 
• The heater must be installed at an angle to allow for sufficient airflow. 
• If the heater is installed without a plug, or with other means for disconnection from 

the supply, a double pole isolator should be used. 

• The heater must not be installed in a recessed area. It must always be surface-

mounted and allow for proper ventilation. Do not allow any heat build-up. 

• Do not install on any plastic or surface other than cement, steel or concrete. 
• Ensure proper insulation when installing on a wooden surface. 
• The minimum ventilation openings around the heater, after installation, must be 

between 10 cm and 20 cm from the top and sides and at least 150 cm away from 
any combustible materials (curtains, paper etc) 

• Remove the foam that protects the lamp during transit before operating the heater. 
• The heater MUST be installed above 1,8 m from the floor surface. 
• Ensure that the heater is properly fixed using the supplied swivel brackets. 
• Permanent wall plugs and or screws should be used. 
• Do not use any form of adhesive tape or temporary fixing. 
• If the supply cord is damaged, it must be replaced by the manufacturer, its service 

agent or similarly qualified persons to avoid a hazard. 

• When installed in a bathroom / Jacuzzi area, install in such a way that the heater, 

switches and other controls cannot be touched by a person in the bath

Summary of Contents for G3 1000 G













Reviews: