StreetStrider Sprinter 3r Owner'S Manual Download Page 15

Street

Strider

 Summit 8r / Sprinter 3r Owner’s Manual     15 

frame and through the other folded pole/ski on the other side 

(Fig. 3-26b)

, then tightening the strap across the front of the joint. A 

second strap around the folded head tube and the main frame 

(Fig. 3-26b)

 

will make the folded 

StreetStrider

 more rigid for easy 

placement onto a rack or into a vehicle. Unfolding the 

StreetStrider

 is now the reverse of the folding process. 

IMPORTANT: 

When the left crank arm is returned to its striding position, make sure that the crank arm bolt is tightened to 
specifications as shown in 

Fig. 3-18. Rotating the Crank Arms

.

  

 

4.  Simple Steps to Learn to Stride                                            

.

 

 

StreetStriding

 is so much fun!  Follow these 9 simple steps to learn to stride.   

   

Step 1.  Safety first                                                                                              

  

Before you stride, make sure you have a CPSC (Consumer Product Safety Commission) approved cycling helmet or other 
helmet to protect your head. Children under 18 years old must wear helmets in some states. If you stride at night, make sure to 
wear light colored or reflective clothing. It is also advised that you equip your 

StreetStrider

 with front and rear lights. Before 

starting any exercise program such as 

StreetStriding

, check with your doctor to make sure you are physically healthy enough.  

 

 

Step 2.  Find a safe, flat place                                                                               

An ideal location to first practice 

StreetStriding

 is a large flat area such as a parking lot with little to no traffic.   

 

 

Step 3.  Engage the brakes when stepping on the 

StreetStrider                   

 

Your 

StreetStrider

 is equipped with both front and rear brakes operated with hand grip levers at the top of each strider pole. Each 

time you are ready to step onto your 

StreetStrider

, first squeeze the brake levers to stabilize the 

StreetStrider

.  

 

  

Step 4.  Step on and get comfortable                                                                

With the brake levers squeezed, step first onto the foot platform that is closest to the ground. Position your foot near the middle 
of the platform. You can always move your foot position while striding to find the ideal spot for your striding style.  

 

 

Step 5.  Become familiar with the brakes and grip shifter                               

In the USA, the 

StreetStrider

 comes with a grip shifter and rear brake lever at the top of the right strider pole, and a front brake 

lever at the top of the left strider pole.  If you live in another country, the cables leading to the brake levers may be switched, 
depending on the specific legal requirements of your country.  The grip shifter will shift the gears of the transmission in the rear 
wheel hub.  Rotate the grip shifter clockwise to shift to a lower gear.  Rotate the grip shifter counter clockwise to shift to a higher 
gear.  Get the feel of how the brakes work by using the left and right brake levers individually to engage and release the front and 
rear brakes while rolling slowly forward.  When you need to stop quickly, engage both front and rear brakes simultaneously.   

 

Step 6.  Find the best gear                                                                                  

The 

StreetStrider

 Summit 8r has 8 gears and the Sprinter 3r has 3 gears.  Gears 1, 2 and 3 of the Sprinter 3r have similar ratios 

to gears 4, 6 and 8 of the Summit 8r.  When you stride on flat ground, shift to one of the higher gears to get the smoothest arm 
and leg motion.  As you stride on changing grades, shift gears up or down to achieve the optimum speed and revolutions per 
minute (RPMs) for your striding style and exercise goals.  When climbing a hill, shift to the lower gears.  When cruising downhill, 
shift to the higher gears.   

 

Step 7.  Lean to steer                                                                                           

Your 

StreetStrider

 is equipped with a lean-to-steer system. To make a turn, simply lean or shift your body weight a little bit in the 

direction of the turn and the 

StreetStrider

 will begin to turn. The more you lean, the more the 

StreetStrider

 turns.  To assist with 

turning, you can lower the foot platform on the inside of the turn. Although this isn’t necessary, it can make turning seem 
easier. At low speed, your 

StreetStrider

 can also be turned by moving both strider poles sideways, which causes the strider to 

lean in the direction of the turn.   

 

 

Step 8.  Cruise a bit                                                                                             

Before you go out on the road or bike path, it is a good idea to practice using your 

StreetStrider

 in a safe area. We recommend 

practicing right and left turns, braking and gear shifting using these instructions.

 

 

Step 9.  Have fun                                                                                                  

Now get out there and enjoy your 

StreetStrider

! You’ll have a blast and burn calories too!   

Summary of Contents for Sprinter 3r





















Reviews: