6
Copyright © 2019 StreetStrider International, LLC
#
DESCRIPTION
HARDWARE
SPECIFICATIONS
QTY
STATE
1
Main frame bone
AL 6061 T6
1
2
Head tube
Bottle cage bosses
Strut coupling boss
M5 x P0.8 threads, 2 front side, 1 rear side
2
Tighten to secure
cage and coupling
3
Crossbar
1
4
Front beam
Clevis bracket with
adjustable caster angle
Male and female 52 tooth spline
M31 x P1.0 lock ring
M10 x P1.5 x L20 x W8, center screw
2
Tighten after
adjusting caster
angle
5
Fold joint
Quick Release clamp stem
nylon lock nut
M6 x P1.0 x L20 x H10 x W10
1
Snug to secure
6
Stride pole upper
Left and right side
2
7
Strider pole lower
2
8
Frame strut
Coupling at top end
Saddle at bottom end
¾” x 11.5 TPI GHT, M5 x P0.8 inner face
M5 x P0.8 binding screw w/ nylon washers
1
1
Tighten
Snug
9
Strider ski
Composite bushings
Roller bearings
OD12 x ID10 x L15 x 17 mm flange, at Joint #2
OD 26 x ID 18 x L 20, at Joint #3
4
4
Grease
Grease
10
Foot platform
4 mm hex screw,
Grip tape on surface
M5 x P0.8 x L12 x H12 x W4,
12
Tighten
11
Rear fender frame
4 mm hex screw,
M5 x P0.8 threaded hole for luggage rack
1
Tighten
12
Fender stay
2
13
Chain stay
2
14
Hand grip
Left and right side, rubber
2
15
Twist grip shifter
3 mm hex screw
M4 x P0.7 x L16 x W3, clamp
1
Tighten
16
Brake lever
5 mm hex screw
Parking pin
Cable housing adjuster
Cable doubler
M5 x P0.8 x L20 x H10 x W5, clamp
OD 10, spring loaded
M10 x P2.0 barrel adjuster with lock ring
Front brake, with adjuster and lock ring
2
2
2
1
Tighten
Adjust-lock
Adjust-lock
17
Joint #1, cross bar-pole
pivot clamp assembly
4 mm hex screw
3 mm hex set screw
4 mm hex pan head
Roller bearings
4 mm flat head screw
M5 x P0.8 x L30 x H8 x W4, clamp cap
M6 x P1.0 x L5 x W3, with cup end, cross bar
M6 x P1.0 x L10 x W4, lock screw
OD26 x ID18 x L20, in cross bar
M6 x P1.0 x L20 x W4, inner shaft end
8
8
2
4
2
Tighten evenly to
secure pole
Tighten
Tighten
Grease
Tighten
18
Joint #2, pole-ski pivot
8 mm hex screw,
washer,
17 mm nut
M10 x P1.5 x L75 x H15 x W8
OD16 x ID10 x T1
M10 x P1.5 x L10 x W17, nylon lock
2
2
2
Snug but allow joint
movement
19
Joint #3, ski-pedal pivot
6 mm hex spindle
OD18 X L60 x W6, 9/16” x 20 TPI
Right threads right, Left threads left, C clip
2
Tighten
20
Front beam pivot
8 mm hex screw
3 mm hex set screw
Tapered roller bearing
M10 x P1.5 x L20 x W8, front cap
M6 x P1.0 x L5 x W3, rear end
OD 47 x ID 20 X T15
1
1
2
Tighten
Tighten
Grease
Figure 2-1
StreetStrider 8s Parts List with Hardware Specifications.