Streak 800Pro Instruction Manual Download Page 2 | Manualshive

Page: 2 / 24

Streak 800Pro Instruction Manual Download Page 2

Contents

1. Safety Notes........................................................................................................................................................3
2. Equipment Required For Assembly....................................................................................................................4
3. Check List............................................................................................................................................................5
4.1 Assembly Steps - Flight direction indicator......................................................................................................8
4.2 Assembly Steps – Motor....................................................................................................................................9
4.3 Assembly Steps – Motor Mount .....................................................................................................................10
4.4 Soldering Job...................................................................................................................................................11
4.5 Assembly Steps – ESC and ESC board...........................................................................................................12
4.6 Assembly Steps – Motors & Propellers...........................................................................................................14
4.7 Assembly Steps – Bipod Landing Gear...........................................................................................................16
5. Quick Collapsible Illustration...........................................................................................................................18
6. Gimbal Mounting..............................................................................................................................................20
7. Multicopter Controller Mounting Illustration...................................................................................................22
8. Specification......................................................................................................................................................23
End Of Manual......................................................................................................................................................24

2

«
1
2
3
4
...
»

Summary of Contents for 800Pro

























Reviews:

No comments