manualshive.com logo in svg

Stratus ftServer 2900 Series, Planning And Installation Manual

Share
Download
Stratus ftServer 2900 Series Planning And Installation Manual Download Page 107

Connecting the ftServer System to External Storage Systems

Connecting the System Components and Peripherals

10-5

For more information, see 

“Supported Storage Systems” 

on page 4-2

.

The following configurations are supported: 

Directly attach the Fibre Channel cables between one or two ftServer systems and 
the Fibre Channel RAID controllers of a supported ftScalable Storage system

Connect multiple ftServer systems to a supported ftScalable Storage storage 
systems through a storage area network (SAN) 

Connect multiple ftServer systems to iSCSI RAID controllers in a supported 
ftScalable Storage system through a switch in a LAN 

If you are connecting an external storage system for data storage only, make the 
connections 

after

 you install the operating system and verify that the operating system 

is operating properly.

For Linux- or VMware vSphere-based systems only, if you are installing 
Automated Uptime Layer on a volume or LUN (logical unit number) of a Fibre Channel 
storage system to create a boot volume, make the connections 

before

 you install the 

software.

For information about installing, connecting, and configuring your external storage 
system to an ftServer system, see one or more of the following:

The 

ftScalable Storage G3: Getting Started Guide

(R687). 

The links in the 

ftScalable Storage G4 System Documentation

 section in the 

Preface.

For VMware vSphere-based systems, also see the 

VMware 

vSphere Storage

 

guide, which explains the best practices for configuring storage systems in a 
VMware vSphere environment and provides information about managing VMware 
vSphere-based systems that use a SAN.

For connecting to network switches to access iSCSI storage systems on the same 
subnet, see 

“Connecting ftServer Systems to the Network for iSCSI Access” on 

page 10-5

. 

Connecting ftServer Systems to the Network for iSCSI Access 

You can use one of the following network ports to connect ftServer systems to 
supported ftScalable Storage system iSCSI storage devices:

The embedded 1GbE or 10GbE LAN adapters

The supported, optional Ethernet PCI adapters. See 

Table 7-3

, 

Table 7-4

, or 

Table 7-5

 for information about supported Ethernet PCI adapters. 

Summary of Contents for ftServer 2900 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands