manualshive.com logo in svg

Stratus ftServer 2900 Series, Planning And Installation Manual

Share
Download
Stratus ftServer 2900 Series Planning And Installation Manual Download Page 65

Peripheral Components for Windows-based Systems

 

Site Planning for Peripheral Components

7-3

Peripheral Components for Windows-based Systems

Table 7-3

 lists the PCI adapters required for each peripheral component on ftServer 

systems running Automated Uptime Layer for Windows-based ftServer Systems. 

To plan a site for a system on which Automated Uptime Layer and the Windows 
operating system are installed, see the previous chapters in this manual. Also, see the 
following manuals:

The 

ftScalable Storage G3: Getting Started Guide

(R687) for information about 

connecting ftScalable Storage G3 systems to ftServer systems 

The 

Stratus ftServer Systems: PCI Adapter Guide

(R461) for detailed information 

about the PCI adapters 

For additional information about third-party peripheral equipment that has been tested 
with ftServer systems, see the following web site:

http://stratadoc.stratus.com/genref/refsell/qualified_equipment.html

 

Table 7-3. PCI Adapters and Peripheral Components: Windows-based Systems

Components PCI 

Adapters

External SAS tape drive (customer supplied) and ftServer 2900, 
4900, or 6900 system 

U114 Eight-Port SAS PCI-Express 
Adapter

Fibre Channel ftScalable Storage G3 systems and ftServer 
2900, 4900, or 6900 systems 

U112A Single-Port 16-Gbps Fibre 
Channel PCI-Express Adapters 

iSCSI ftScalable Storage G3 systems and ftServer 2900, 4900, 
or 6900 systems 

Embedded Ethernet adapters

U113 Dual-Port 10/100/1000 
Base-T Ethernet PCI-Express 
Adapters

U117A Dual-Port Fiber 
10-Gbps Ethernet PCI-Express 
Adapter

†

 

U118 Dual-Port RJ-45 10-Gigabit 
Ethernet PCI-Express Adapter 

† Supported only in ftServer systems with the PCI-Express (PCIe) riser assembly, which is optional 
in ftServer 4900 systems and standard in ftServer 6900 systems.

Summary of Contents for ftServer 2900 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands