Stratasys Fortus 250mc Site Preparation Manual Download Page 8

4

UNINTERRUPTIBLE POWER SUPPLY (UPS) 

USE AND INSTALLATION

The intent of the Uninterruptible Power Supply (UPS) shutdown feature on Fortus systems is to prevent required 
maintenance and/or system damage by safely shutting the system down in the event of an uncontrolled loss of 
power. Whether an in-process build of a part will complete successfully is dependent on the battery life of the 
selected UPS and the duration of the power outage.

The user should select a UPS with the following specifications:

• 

Runtime minimum of 15 minutes at 1000W or 2000VA output (run times >15 minutes may be 

appropriate based on the typical duration of power outages at the site).

• 

Runtime minimum 8 minutes after low battery warning tripped.

• 

Peak output (minimum) of 1500W.

• 

Dry contact (voltage free) interface for “On battery” and “Low battery” conditions.

• 

Dry contact interface capable of carrying at least 100mA at 12VDC.

GENERAL INFORMATION

Refer to the UPS and I/O Module (if used)

 

Installation and Operation Guides for instructions on installing the I/O 

module (if used) into the UPS unit as well as for connecting AC power to the UPS and Fortus system. While 
connecting the Fortus system power to the UPS will provide some protection against power outages, the Fortus 
system will shut down safely when “on battery” and “low battery” conditions are detected. Follow the Electrical 
Interface Connection information below.

1. 

Configure Normally Open dry contact relay I/Os of UPS as shown in 

Figure 1

 

(Wired-And configuration).

2. 

Build an appropriate length of UPS to Fortus system cable. See 

Figure 2

 for pin out.

3. 

Connect the cable from the UPS unit’s connector to the UPS (9-pin DSub) connector on the rear 
of the Fortus system.

4. 

Follow the instructions in the UPS Installation and Operation Guide to set the “Low Battery 
Warning Level” to 8 minutes.

Note: 

Make certain to install the jackscrews that hold the cable connectors to their 

respective mates (do not over-tighten)

Note: 

The default low battery warning level value may not provide adequate time to 

ensure the Fortus system can shut down safely.

Summary of Contents for Fortus 250mc













Reviews: