Strata CIX 200 Programming Manual Download Page 469

Page: 469 / 508

Strata CIX Programming Vol.1 12/09

A-1

Ap
pl

ication

Applications Guide

This appendix contains guides to setup and program specific applications such as Voice Mail, IP
Telephony, StrataNet and others.

Voice Mail Set Up

The following steps/program sequences are provided as a guideline to programming system voice mail
settings.

Analog Ports

1. Program 100 Card Slot Assignment. Assign the PCB for voice mail ports (RSTU).

2. Program 200 Station Data. Verify fields 01~04.

•

field 03 Circuit Type – Assigns voice mail to be assigned to PDNs associated with voice mail RSTU
circuits.

•

field 15 Display DN – DN to be displayed and assigned to hunt group. Manually assign DNs and
equipment.

3. Program 209 Station Hunting Group. Voice mail group is determined by the hunt group.

4. Program 218 Station Hunt Group Assignment.

5. Program 579 System Voice Mail Data. Complete, fields 01~17.

Notes

•

10 - Central VM Callback – Enter the node ID and hunt group for voice mail. Used for centralized voice
mail SMDI only.

•

DTMF – Message Waiting Call Back DN across Strata Net TIE lines. DTMF integration uses the
number that displays in Program 200, field 15.

6. Program 580 Voice Mail Port Data. This is the collection of all ports.

7. Program 803 IO Logical Device Assignment. You can add members to the hunt group. Assign RS-232

port for SMDI.

Note

System only provides Code 300 for SMDI. Code 301 is not supported.

8. Program 804 BSIS RS-232 Serial Port setup.

9. Program 309 Direct Inward Dialing.

•

field 11 - DID/DNIS No. Code

•

field 15 - VM Application Digits

10.Program 318 DID Intercept Assignment.

•

field - 11 DID/DNIS No. VMID

•

field - 15 DID/DNIS No. DTMF VMID

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands

Strata CIX 200, Programming Manual

Search results

Summary of Contents for CIX 200

Reviews:

Related manuals for CIX 200

Brands by name

Popular brands