Strata CIX 200 Programming Manual Download Page 394 | Manualshive

Page: 394 / 508

background image

Services

SMDR

9-44

Strata CIX Programming Vol.1 12/09

513 SMDR for ILG Assignment

Prerequisite Program:

None

This program assigns SMDR parameters for ILGs.

07 Global Call ID Number

Enable - allow the Global Call ID Number to be generated in the SMDR data.

Disable - the Global Call ID Number will not be generated in the SMDR data.

Note

The Global Call ID data (15-digit hex characters) is located in
columns 70-84 of the SMDR data stream in the following format:
ZXXXXXXYYYYYYYY

Z

represents the direction of the call (S=originate or source node in

network call, D=destination node in network call, L=single node or
non-Network call.)

X

represents the CIX node ID (6-digit hex characters)

Y

represents the call number (8-digit hex characters)

F

IELD

D

ESCRIPTION

00 Incoming Line Group

(ILG)

Specify the ILG for which to set SMDR parameters.

Possible values:1~6 CTX28, 1~32 CIX40, 1~32 CTX/CIX/100, 1~50 CIX200,

1~50 CTX/CIX 670 BCTU only or BBCU only, 1~128 CTX/
CIX670 BCTU + BEXU or BBCU + BECU, 1~50 CIX1200
HCTU only, 1~128 CIX1200 HCTU + HEXAU, 1~220
CIX1200 HCTU + HEXBU (default = 0)

01 Generate SMDR

Records

Enable to generate records for this ILG.

Possible values:Enable (default) or Disable

02 DNIS Field Indication

Check to include DNIS information in records for this ILG.

Possible values:Enable (default) or Disable

03 Record Incoming

Call

Enable record generation for incoming calls with or without incoming SMDR
being enabled.

Possible values:Enable or Disable (default)

04 Record Abandoned

Calls

Enable record generation for abandoned calls. Incoming SMDR must be
turned on. Abandoned call records are generated whether or not incoming
SMDR has been set.

Possible values:Enable or Disable (default)

05 Display Transferred

Call Records

Select whether to charge a transferred call to the source or destination party.

Possible values:Source (default) or Destination

06 Record QoS

Information

Enabling this options allows QoS information including delay, jitter and packet
loss output to SMDR for incoming VoIP calls. Incoming SMDR must be
turned on.

Possible values:Enable or Disable (default)

F

IELD

D

ESCRIPTION

«
...
392
393
394
395
396
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Damall Pages: 7

Brand: Yealink Pages: 6

Brand: Yealink Pages: 8

Brand: Samsung Pages: 19

Brand: Samsung Pages: 9

Brand: Samsung Pages: 107

Brand: Samsung Pages: 108

Brand: Samsung Pages: 3

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 118

Brand: Samsung Pages: 219

Brand: Samsung Pages: 26

Brand: Samsung Pages: 2

Brand: Samsung Pages: 222

Brand: Samsung Pages: 2

SGH-a887 Series

Brand: Samsung Pages: 189

Brand: Samsung Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands