background image

SPECIFICATIONS 

Width: 40 ft

 

Length: 80 ft

 

Height: 15 ft 

IMPORTANT: READ MANUAL FIRST

 

Improper site preparation, assembly and maintenance may invalidate warranty and cause 
unnecessary and costly mistakes. If you have any questions, contact your local dealer.

 

For an easy assembly process, we have identified each individual component with the part 
code as indicated in the parts list. Please refer to the part code numbers and drawing to 
ensure problem-free assembly. 

It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re

-

tighten once or twice again after a few months of use. This is important when assembled 
during cold seasons (autumn and winter) because the fabric gets stiff in these weather 
conditions. When the weather conditions become warmer, the fabric loosens and needs 
to be re-tighten

 

It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on 

its own. 

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

 

1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set

up near snow drifts, in slippery places, in high winds, or wet locations.

2. All children should be kept away from the work area.
3.

Don’t 

overreach. Always keep proper footing and balance.

4. Do not assemble under the influence of alcohol or drugs. Read warning labels on

medication prescriptions to determine if your judgment or reflexes are impaired
while taking them. If there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these

conditions are likely to occur. Remove the cover during hurricanes.

6. Be careful with power and heat sources. Do not keep heat sources near the

tarpaulin. Do not expose to open flame.

7. Be aware of personal safety during assembly and use. Be careful not to pinch your

fingers with clips and tubes when assembling: When using, make sure there is
adequate ventilation for any dangerous fumes.

Summary of Contents for DT Container shelter












Reviews:

Related manuals for DT Container shelter