background image

 

 

 

SPECIFICATION 

 

 

Width:10m 

Length:12m 

Height:3.6m 

 

 

IMPORTANT ---- READ MANUAL FIRST 

 

 

Improper  site  preparation,  Assembly  and  Maintenance  may  invalidate  warranty  and  cause  unnecessary  and 

costly mistake. If you have any questions contact your local dealer. 

 

For  User  Friendly assembly  we have identified each individual  component with the part  code as indicated in  

the parts list. Please refer to the part code numbers and drawing to ensure problem free assembly. 

 

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten once or 

twice again after a few months of use. This is important when assembly in cold weather (autumn and winter) 

because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric 
“slack” again and need to be re-tighten before next winter. 

 

It’s the owners responsibility to take of snow immediately if not slide off by itself. 

 

 

READ ALL INSTRUCTIONS BEFORE ASSEMBLY 

 
 

 

1.

 

Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in 

high winds, or wet location. 

2.

 

Keep children away. All children should be kept away from the work area. 

3.

 

Don’t over reach. Keep proper footing and balance at all times. 

4.

 

Do  not  assemble  in  under  the  influence  of  alcohol  or  drugs.  Read  warning  labels  on  prescriptions  to 

determine  if  your  judgment  or  reflexes  are  impaired  while  taking  drugs.  If  there  is  any  doubt,  do  not 

assemble. 

5.

 

Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur. 

Remove the cover during hurricane. 

6.

 

Be  careful  with  power  and  heat  sources.  Do  not  keep  heat  sources  near  the  tarpaulin.  Do  not  expose  to  

open flame. 

7.

 

Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips and tubes 

when  assembling:  when  using  makes  sure  there  is  adequate  ventilation  for  exhaust  and  other  dangerous 

fumes. 

Summary of Contents for C3340S














Reviews: