Stones Sound Studio Ribbon 260 Manual Download Page 8

 

8

 

 

 

 

 

Loudspeaker Description

 

Crossover 260 260C 360 
The Linkwitz Riley (Bessel /Butterworth) crossover unit was  developed to enable good   linear phase and minimum 
THD  distortion through the pass band and over lap regions  of both the woofer and ribbon tweeter whilst  providing  
wide  dynamic range and excellent  low  mid and high level continuity of detail .  
A 2nd order low pass with a 3rd order high pass filter slope was chosen after evaluating many different design 
combinations to provide optimum isolation between low and high frequencies. Time compensation of the driver xyz 
location and  rising peaks response in the woofer and tweeter on and off axis were reduced  buy fine tuning crossover  
component values thus enabling coherent   coupling from bass to tweeter combination through out the crossover 
region. The fully finished crossover PCB includes all components, high quality internal wiring and Velcro mounting 
tabs 

 

 

 
Components used in the Ribbon Speaker crossover are High quality Non-Inductive resistors, Copper Air core 
Inductors, SCR 400V metalized MKP capacitors.OFC 384 strand copper wiring  
Crossover Features Summary 

 

Fully finished PCB includes all components and wiring ready to install 

 

Soldering: None required Wiring cable: Internal speaker cable high quality OFC 384 strand with push on 
connections 

 

Speaker terminals: 4mm twin gold plated binding post 

 

Filter 2 way off set Bessel / Butterworth, linear phase 

 

Frequency: 260 260c  3.8 KHz 360 Freq  3.2Khz 

 

Order: 2nd Lp, 3rd Hp 
Speaker Cable type internal wiring & amplifier 
OFC 384-speaker cable is made from a low loss pure OFC copper. The cable is a type of Litz wire construction 
formed from   384 thin copper wires woven into a low profile flat rectangular shape and then insulated with a clear 
polymer jacket. This excellent combination of  shape and size  ensures  the OFC 384 speaker cable has  minimal 
HF loss from the skin effect found in round conductors and also enables a lower overall  impedance which 
provides better  bass depth, midrange  transients and dynamics. 
Other speaker  cable I recommend to are QED Nordost Chord Kimber Audio Quest  

 

Summary of Contents for Ribbon 260

































Reviews: