background image

 

4.

 

WARNING: This appliance gets hot and it contains internal parts that could arc or spark. Do not use it in 

areas where gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to 

flammable vapors.    Do not use near propane tanks.   

5.

 

WARNING:  This fireplace should not be used as a drying rack for clothing.  Do not hang Christmas 

stocking or any decoration on the fireplace heater or mantle.     

6.

 

Extreme caution is necessary when any heater is used by or near children or those with disabilities.   

7.

 

Do not operate the heater unattended or while sleeping.    Stay alert and monitor operation at all times. 

8.

 

Always unplug fireplace when not in use. 

9.

 

Do not operate any fireplace heater with a damaged cord or plug, or if the heater has malfunctioned, or if the 

fireplace has been dropped or damaged in any manner. Take fireplace to authorized service facility for 

examination, electrical or mechanical adjustment or repair. 

10.

 

Check your heater  cord and plug connections. A loose fitting outlet can cause the plug to overheat and/or 

cause a fire. Be sure plug fits tight in the outlet. Check frequently during use to make sure plug and outlet 

are not hot. If so, discontinue using heater immediately and have outlet replaced by a qualified electrician.   

CAUTION: Heaters draw more current than small appliances, overheating of the outlet may occur even if it 

has not occurred with the other appliances. 

11.

 

Under no circumstance should this electric fireplace be modified.    Parts having to be removed for servicing 

must be replaced by a certified repair center prior to operating this electric fireplace again. 

12.

 

Do not use outdoors or anywhere that it can get wet. 

13.

 

This fireplace is not intended for use in bathrooms,  laundry areas and similar indoor locations. Never use 

this appliance near a bathtub or in the vicinity of water. 

14.

 

Do not place or operate the fireplace insert directly on carpet or a similar surface, which may restrict air 

circulation beneath the unit.    The fireplace insert must be installed in the mantle before use. 

15.

 

To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces, like 

a bed, where openings may become blocked. 

16.

 

Do  not run cord under carpeting, furniture or appliances. Do  not cover cord with carpeting, throw rugs, 

runners, or the like. Arrange cord away from traffic area and where it will not be tripped over. 

17.

 

To disconnect fireplace, turn all controls to off, then remove plug from outlet. 

18.

 

Grounding – this heater is for use on 120 volts.    The cord has a plug with three blades for proper grounding.   

DO NOT attempt to modify the plug in any way or use adaptors to defeat the purpose of the grounding 

feature.  Plug ONLY into a receptacle that accepts three-blade plugs.  CAUTION: To Prevent Electric 

Shock Match Wide Blade of Plug to Wide Slot of Outlet, Fully Inserted.   

19.

 

When this appliance is installed, it must be electrically grounded in accordance with local codes with the 

current CSA C22.1 Canadian local codes for USA installation.    Follow local codes and National Electrical 

Code, ANSI/NFPA NO. 70 and Canadian Code, CZ 22.2 No. 0. 

20.

 

Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an 

electric shock or fire, or damage the heater. 

21.

 

Do not modify this fireplace. Use it only as described in this manual. Any other use not recommended by the 

manufacturer may cause fire, electric shock or injury to persons. 

22.

 

WARNING:  NEVER USE WITH AN EXTENSION CORD OR RE-LOCATABLE POWER STRIP.  An 

extension cord may overheat and cause a risk of fire.   

23.

 

Do not burn wood or other materials in this fireplace. 

Summary of Contents for Melrose Dark Cherry


















Reviews: