Stoelting 4231G Owner'S Manual Download Page 29

Page: 29 / 43

SECTION 5

REPLACEMENT PARTS

5.1

HOW TO ORDER PARTS

To assure receipt of the proper replacement parts, supply
your dealer or distributor with the following information:

A. Model number of equipment.

B. Serial number of model, stamped on nameplate.

Part Number

Description

324014

Decal Black Arrow

324141

Decal Caution Rotating Blades

324509

Decal Cleaning

324548

Decal Ventilation

324346

Decal Caution

324393

Decal – Drip Tray

324803

Decal – Header Panel (Stoelting Logo)

324804

Decal - Header Panel (Stoelting Swirl)

324806

Decal - Header Panel (A & W Logo)

324798

Decal – CLEAN/OFF/SERVE

324125

Decal – Elec. Shock Hazard

C. Part number, part name and quantity needed.

Common part names and numbers are listed in this
manual.

5.2

PUSH TO FREEZE LIGHT/SWITCH
LAMP REPLACEMENT

To change a lamp in the PUSH TO FREEZE switch/light
follow these simple steps:

A. Grasp the lens with your thumb and forefinger and

pull out.

B. Remove the faulty lamp by pulling out the lamp puller

(See Fig. 33).

Figure 33. Push To Freeze Light/Switch Assembly

C. To install the new lamp, line up the lamp end with the

receptacle and push fully in.

D. Reinstall the lens by pushing firmly in. When installed

“PUSH TO” might be right side up.

NOTE

LED light bulbs require correct polarity. If the bulb
does not illuminate, remove the bulb, turn 180°
and replace.

5.3

CLEAN-OFF-SERVE ROCKER
SWITCH REPLACEMENT

A. Remove side panel.

WARNING

DISCONNECT FREEZER FROM ELECTRICAL
SUPPLY SOURCE BEFORE SERVICING.

Summary of Contents for 4231G












































Search results

Summary of Contents for 4231G

Reviews:

Related manuals for 4231G

Brands by name

Popular brands

Stoelting 4231G, Owner'S Manual

Search results

Summary of Contents for 4231G

Reviews:

Related manuals for 4231G

Brands by name

Popular brands