DocID024995 Rev 4
43/104
STM32L100RC
96
6.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 9: Voltage characteristics
Table 10: Current characteristics
, and
Table 11: Thermal characteristics
may cause
permanent damage to the device. These are stress ratings only and functional operation of
the device at these conditions is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
Table 9. Voltage characteristics
Symbol
Ratings
Min
Max
Unit
V
DD
–V
SS
External main supply voltage
(including V
DDA
and V
DD
)
(1)
–0.3
4.0
V
V
IN
(2)
Input voltage on five-volt tolerant pin
V
SS
−
0.3
V
DD
+4.0
Input voltage on any other pin
V
SS
−
0.3
4.0
|
Δ
V
DDx
|
Variations between different V
DD
power pins
-
50
mV
|V
SSX
−
V
SS
|
Variations between all different ground pins
-
50
V
REF+
–V
DDA
Allowed voltage difference for V
REF+
> V
DDA
-
0.4
V
V
ESD(HBM)
Electrostatic discharge voltage
(human body model)
1.
All main power (V
DD
, V
DDA
) and ground (V
SS
, V
SSA
) pins must always be connected to the external power supply, in the
permitted range.
2.
V
IN
maximum must always be respected. Refer to
for maximum allowed injected current values.
Table 10. Current characteristics
Symbol
Ratings
Max.
Unit
I
VDD(
Σ
)
Total current into sum of all V
DD_x
power lines (source)
(1)
100
mA
I
VSS(
Σ
)
(2)
Total current out of sum of all V
SS_x
ground lines (sink)
(1)
100
I
VDD(PIN)
Maximum current into each V
DD_x
power pin (source)
(1)
70
I
VSS(PIN)
Maximum current out of each VSS_x ground pin (sink)
(1)
-70
I
IO
Output current sunk by any I/O and control pin
25
Output current sourced by any I/O and control pin
- 25
Σ
I
IO(PIN)
Total output current sunk by sum of all IOs and control pins
(2)
60
Total output current sourced by sum of all IOs and control pins
(2)
-60
I
INJ(PIN)
(3)
Injected current on five-volt tolerant I/O
(4)
, RST and B pins
-5/+0
Injected current on any other pin
(5)
± 5
Σ
I
INJ(PIN)
Total injected current (sum of all I/O and control pins)
(6)
± 25
1.
All main power (V
DD
, V
DDA
) and ground (V
SS
, V
SSA
) pins must always be connected to the external power supply, in the
permitted range.
2.
This current consumption must be correctly distributed over all I/Os and control pins. The total output current must not
be sunk/sourced between two consecutive power supply pins referring to high pin count LQFP packages.
3.
Negative injection disturbs the analog performance of the device. See note in
4.
Positive current injection is not possible on these I/Os. A negative injection is induced by V
IN
<V
SS
. I
INJ(PIN)
must never
be exceeded. Refer to
for maximum allowed input voltage values.
微可Vicor——值得信赖的元器件供应商
http://www.vicor.top/
021-31660491
微可Vicor——值得信赖的元器件供应商
http://www.vicor.top/
021-31660491
