manualshive.com logo in svg

STMicroelectronics STM32F405, Reference Manual

The STMicroelectronics STM32F405 is a powerful microcontroller featuring a Cortex-M4 core, ideal for embedded applications. To get the most out of this product, make sure to download the free Reference Manual from manualshive.com. The manual provides detailed information on how to maximize the STM32F405's capabilities.

Share
Download
background image

DocID018909 Rev 11

869/1731

RM0090

Serial peripheral interface (SPI)

918

device is configured in slave mode (refer to 

Section 28.3.10: Error flags on page 889

). 

A basic example of interconnections between a single master and a single slave is 
illustrated in 

Figure 247

.

Figure 247. Single master/ single slave application

1. Here, the NSS pin is configured as an input.

The MOSI pins are connected together and the MISO pins are connected together. In this 
way data is transferred serially between master and slave (most significant bit first).

The communication is always initiated by the master. When the master device transmits 
data to a slave device via the MOSI pin, the slave device responds via the MISO pin. This 
implies full-duplex communication with both data out and data in synchronized with the 
same clock signal (which is provided by the master device via the SCK pin).

Slave select (NSS) pin management

Hardware or software slave select management can be set using the SSM bit in the 
SPI_CR1 register.

•

Software NSS management (SSM = 1)
The slave select information is driven internally by the value of the SSI bit in the 
SPI_CR1 register. The external NSS pin remains free for other application uses.

•

Hardware NSS management (SSM = 0)
Two configurations are possible depending on the NSS output configuration (SSOE bit 
in register SPI_CR2).
–

NSS output enabled (SSM = 0, SSOE = 1)
This configuration is used only when the device operates in master mode. The 
NSS signal is driven low when the master starts the communication and is kept 
low until the SPI is disabled. 

–

NSS output disabled (SSM = 0, SSOE = 0)
This configuration allows multimaster capability for devices operating in master 
mode. For devices set as slave, the NSS pin acts as a classical NSS input: the 
slave is selected when NSS is low and deselected when NSS high.

Clock phase and clock polarity

Four possible timing relationships may be chosen by software, using the CPOL and CPHA 
bits in the SPI_CR1 register. The CPOL (clock polarity) bit controls the steady state value of 

8-

b

it shift register

SPI clock
generator

8-

b

it shift register

MISO

MOSI

MOSI

MISO

SCK

SCK

Slave

Master

NSS

(1)

NSS

(1)

V

DD

MSBit

LSBit

MSBit

LSBit

Not used if NSS is managed

 

b

y software

ai14745

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

D-Link DSN-640 Quick Installation Manual preview
DSN-640
Brand: D-Link Pages: 40
Saitek P880 User Manual preview
P880
Brand: Saitek Pages: 44
Balmar Max Charge MC-624 Installation And Operator'S Manual preview
Max Charge MC-624
Brand: Balmar Pages: 8
Balmar MAX CHARGE MC-614 Installation And Operation Manual preview
MAX CHARGE MC-614
Brand: Balmar Pages: 20
Harpo BraillePen 12 Quick Start Manual preview
BraillePen 12
Brand: Harpo Pages: 35
Hardi HC 6500 Quick Manual preview
HC 6500
Brand: Hardi Pages: 2
Fingertips Lab O6 Quick Start Manual preview
O6
Brand: Fingertips Lab Pages: 15
xpr VPROX2-M User Manual preview
VPROX2-M
Brand: xpr Pages: 4
J+J J4C S20 Quick Start Manual preview
J4C S20
Brand: J+J Pages: 4
Val Controls I 24-AF Series Replacement Manual preview
I 24-AF Series
Brand: Val Controls Pages: 6
Heat & Cool HCUMR-903 Operation Manual preview
HCUMR-903
Brand: Heat & Cool Pages: 5
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Brand: H.E. Anderson Pages: 11
Allen-Bradley CENTERLINE Instruction Manual preview
CENTERLINE
Brand: Allen-Bradley Pages: 88
Grundfos DDI Series Supplement To Installation And Operating Instructions preview
DDI Series
Brand: Grundfos Pages: 12
Stevens Smart PT User Manual preview
Smart PT
Brand: Stevens Pages: 16
Fagor 8040 CNC - FEATURES Manual preview
8040 CNC - FEATURES
Brand: Fagor Pages: 247
We TARVOS-III Migration Manual preview
TARVOS-III
Brand: We Pages: 27
Lumel re72 series Quick Start Manual preview
re72 series
Brand: Lumel Pages: 32

Brands by name

Popular brands

Load more brands