STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 1372 / 1731

background image

USB on-the-go high-speed (OTG_HS)

RM0090

DocID018909 Rev 11

Figure 410. USB OTG interface block diagram

1. The USB DMA cannot directly address the internal Flash memory.

35.3.1

High-speed OTG PHY

The USB OTG HS core embeds an ULPI interface to connect an external HS phy.

35.3.2

External Full-speed OTG PHY using the I2C interface

The USB OTG HS core embeds an I

2

C interface allowing to connect an external FS phy.

35.3.3

Embedded Full-speed OTG PHY

The full-speed OTG PHY includes the following components:

•

FS/LS transceiver module used by both host and Device. It directly drives transmission
and reception on the single-ended USB lines.

•

Integrated ID pull-up resistor used to sample the ID line for A/B Device identification.

•

DP/DM integrated pull-up and pull-down resistors controlled by the OTG_HS core
depending on the current role of the device. As a peripheral, it enables the DP pull-up
resistor to signal full-speed peripheral connections as soon as V

BUS

is sensed to be at

a valid level (B-session valid). In host mode, pull-down resistors are enabled on both
DP/DM. Pull-up and pull-down resistors are dynamically switched when the peripheral
role is changed via the host negotiation protocol (HNP).

•

Pull-up/pull-down resistor ECN circuit
The DP pull-up consists of 2 resistors controlled separately from the OTG_HS as per
the resistor Engineering Change Notice applied to USB Rev2.0. The dynamic trimming

!("MASTERINTERFACE

!("SLAVEINTERFACE

#05

-EMORY

0ERIPHERAL

0ERIPHERAL

5,0)INTERFACE

5,0)0(9

53"

$ATA&)&/

SINGLEPORT2!-

302!-

$ATA&)&/

2!-INTERF

ACE

)NTERRUPT

!("APPLICATIONB

US

53"/4'(3CORE

AIB

«
...
1370
1371
1372
1373
1374
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Evolution Series E9000

Brand: GE Pages: 44

PACSystems RX7i

Brand: GE Pages: 469

GuardSwitch 300 Series

Brand: GE Pages: 2

GuardSwitch 300 Series

Brand: GE Pages: 2

Masoneilan VariPak 28001

Brand: GE Pages: 24

Brand: GE Pages: 425

Brand: Magnescale Pages: 132

Brand: Van Air Pages: 4

Brand: Watlow Pages: 59

Tekmar WiFi Snow Melting Control 670

Brand: Watts Pages: 48

Spartan-3A DSP FPGA Series

Brand: Xilinx Pages: 140

GRASS VALLEY MDX-3901

Brand: Belden Pages: 45

Brand: Vag Pages: 12

Brand: Euromatic Pages: 20

Brand: VMK Pages: 98

AQUIS ULTRAFLOW

Brand: Waterous Pages: 217

Brand: zeeltronic Pages: 13

Brand: QD Dynamics Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands