STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 1114 / 1731

background image

Ethernet (ETH): media access control (MAC) with DMA controller

RM0090

DocID018909 Rev 11

33.2.1 MAC

core

features

•

Supports 10/100 Mbit/s data transfer rates with external PHY interfaces

•

IEEE 802.3-compliant MII interface to communicate with an external Fast Ethernet
PHY

•

Supports both full-duplex and half-duplex operations
–

Supports CSMA/CD Protocol for half-duplex operation

–

Supports IEEE 802.3x flow control for full-duplex operation

–

Optional forwarding of received pause control frames to the user application in full-
duplex operation

–

Back-pressure support for half-duplex operation

–

Automatic transmission of zero-quanta pause frame on deassertion of flow control
input in full-duplex operation

•

Preamble and start-of-frame data (SFD) insertion in Transmit, and deletion in Receive
paths

•

Automatic CRC and pad generation controllable on a per-frame basis

•

Options for automatic pad/CRC stripping on receive frames

•

Programmable frame length to support Standard frames with sizes up to 16 KB

•

Programmable interframe gap (40-96 bit times in steps of 8)

•

Supports a variety of flexible address filtering modes:
–

Up to four 48-bit perfect (DA) address filters with masks for each byte

–

Up to three 48-bit SA address comparison check with masks for each byte

–

64-bit Hash filter (optional) for multicast and unicast (DA) addresses

–

Option to pass all multicast addressed frames

–

Promiscuous mode support to pass all frames without any filtering for network
monitoring

–

Passes all incoming packets (as per filter) with a status report

•

Separate 32-bit status returned for transmission and reception packets

•

Supports IEEE 802.1Q VLAN tag detection for reception frames

•

Separate transmission, reception, and control interfaces to the Application

•

Supports mandatory network statistics with RMON/MIB counters (RFC2819/RFC2665)

•

MDIO interface for PHY device configuration and management

•

Detection of LAN wakeup frames and AMD Magic Packet™ frames

•

Receive feature for checksum off-load for received IPv4 and TCP packets
encapsulated by the Ethernet frame

•

Enhanced receive feature for checking IPv4 header checksum and TCP, UDP, or ICMP
checksum encapsulated in IPv4 or IPv6 datagrams

•

Support Ethernet frame time stamping as described in IEEE 1588-2008. Sixty-four-bit
time stamps are given in each frame’s transmit or receive status

•

Two sets of FIFOs: a 2-KB Transmit FIFO with programmable threshold capability, and
a 2-KB Receive FIFO with a configurable threshold (default of 64 bytes)

•

Receive Status vectors inserted into the Receive FIFO after the EOF transfer enables
multiple-frame storage in the Receive FIFO without requiring another FIFO to store
those frames’ Receive Status

•

Option to filter all error frames on reception and not forward them to the application in

«
...
1112
1113
1114
1115
1116
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: Barthelme Pages: 8

Brand: CAB Pages: 28

Brand: C-TEC Pages: 16

Brand: C&T Solution Pages: 27

SECURIT ST800L+

Brand: C&K systems Pages: 16

Brand: Datavideo Pages: 8

Brand: H3C Pages: 69

Brand: Laars Pages: 28

U1000 iQpump Drive

Brand: YASKAWA Pages: 426

Brand: YASKAWA Pages: 26

Brand: YASKAWA Pages: 210

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 400

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 466

Brand: V2 Pages: 12

Brand: H3C Pages: 5

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

Brand: Savant Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands