STMicroelectronics SPEAr300 Reference Manual Download Page 523 | Manualshive

Page: 523 / 844

background image

RM0082

HS_Media independent interface (MII)

Doc ID 018672 Rev 1

●

SWR

Setting this bit, the DMA Controller resets all MAC internal registers and logic. This bit
is automatically cleared after the reset has completed.

24.7.4

Transmit poll demand register (Register1, DMA)

The Transmit Poll Demand is a register which enables the transmit DMA to check whether or
not the current descriptor is owned by DMA. The transmit poll demand bit assignments are
given in

●

TPD

When these bits are written with any value, the DMA reads the current descriptor
pointed to by DMA Register18 (

Current Host Transmit Descriptor)

. If the pointed

descriptor is available the transmission resumes, otherwise (that is, the descriptor is
owned by the host), transmission returns to suspend state and TU bit in DMA Register5
(

Status)

is asserted.

24.7.5

Receive poll demand register (Register2, DMA)

The Receive Poll Demand is a register which enables the receive DMA to check for new
descriptors. The Receive Poll Demand bit assignments are given in

●

RPD

When these bits are written with any value, the DMA reads the current descriptor
pointed to by DMA Register19

(Current Host Receive Descriptor)

. If the pointed

descriptor is available the reception resumes, otherwise (that is, the descriptor is
owned by the host), reception returns to suspend state and RU bit in DMA Register5

(Status)

is asserted.

24.7.6

Receive descriptor list address register (Register3, DMA)

The receive descriptor list address is a register which points to the start of the Receiver
Descriptor List. The Receive Descriptor List address bit assignments are given in

VALUE

ARBITRATION SCHEME

1‘b0

Round robin with Rx:Tx priority given in PR field.

1‘b1

Rx has priority over Tx.

Table 426.

Transmit poll demand register bit assignments

Bit

Name

Reset Value

Type

Description

[31:00]

TPD

32’h0

RW

Transmit Poll Demand.

Table 427.

Receive poll demand register bit assignments

Bit

Name

Reset Value

Type

Description

[31:00]

32’h0

RW

Receive Poll Demand.

«
...
521
522
523
524
525
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Leroy-Somer R180

Brand: Nidec Pages: 20

Brand: UCS Pages: 4

MorphoAccess SIGMA Extreme Series

Brand: Idemia Pages: 31

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 20

Brand: Koer Pages: 6

HmIP-FAL230-C10

Brand: HomeMatic Pages: 42

Brand: Airlow Pages: 20

Brand: Infineon Pages: 28

Brand: Toho Electronics Pages: 32

SR-ZV9002T4-CCT-RU

Brand: Z-Wave Alliance Pages: 10

Triad Controls WE Series

Brand: A-T Controls Pages: 13

Brand: Texas Instruments Pages: 19

StreamMax Pump Controller

Brand: Oase Pages: 142

Brand: DELTA DORE Pages: 9

ARES-1231 Series

Brand: Arbor Technology Pages: 94

Brand: Danfoss Pages: 18

Brand: Zapi Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands