STMicroelectronics SPEAr300 Reference Manual Download Page 517

Page: 517 / 844

RM0082

HS_Media independent interface (MII)

Doc ID 018672 Rev 1

517/844

24.7 Programming

model

24.7.1 Register

map

The MAC-UNIV can be fully configured by programming a set of 32 bit wide registers which
can be accessed at the base address 0xE080_0000.

The MAC-UNIV registers can be grouped in two different classes:

●

DMA registers

(listed in

Table 422.

)

●

MAC registers

(listed in

Table 423.

)

Table 422.

MAC-UNIV DMA registers summary

Name

Offset

Reset value Description

0x1000

32’h0

Bus Mode Register.

0x1004

32’h0

Transmit Poll Demand Register.

0x1008

32’h0

Receive Poll Demand Register.

0x100C

32’h0

Receive Descriptor List Address Register.

0x1010

32’h0

Transmit Descriptor List Address Register.

0x1014

32’h0

Status Register.

0x1018

32’h0

Operation Mode Register.

0x101C

32’h0

Interrupt Enable Register.

0x1020

32’h0

Missed Frame And Buffer Overflow Counter Register.

0x1024
to
0x1044

Reserved.

32’h0

Current Host Transmit Descriptor Register.

32’h0

Current Host Receive Descriptor Register.

32’h0

Current Host Transmit Buffer Address Register.

32’h0

Current Host Receive Buffer Address Register.

Table 423.

MAC-UNIV MAC global registers summary

Name

Offset

Reset value

Description

0x0000

32’h0

Mac Configuration Register.

0x0004

32’h0

Mac Frame Filter Register.

0x0008

32’h0

Hash Table High Register.

0x000C

32’h0

Hash Table Low Register.

0x0010

32’h0

Mii Address Register.

0x0014

32’h0

Mii Data Register.

0x0018

32’h0

Flow Control Register.

0x001C

32’h0

Vlan Tag Register.

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands

STMicroelectronics SPEAr300, Reference Manual

Search results

Summary of Contents for SPEAr300

Reviews:

Related manuals for SPEAr300

Brands by name

Popular brands