13
REAR PANEL
1. Power Switch
This switch controls the AC mains power to your
powered mixer. Power is on when the switch is in
the on(up) position and is confirmed when the power
LED indicator is illuminated.
Note : Before turing on or off the mixer. It is a good idec to
turn down the main master and monitor master controls.
2. FUSE
The fuse is located in the fuse holder. (See Section
Ⅷ
Specifications for the correct values.)
3. IEC Socket
This is where you connect the supplied AC line cord to
provide
AC power to the all VM series powered mixer. Plug the line
cord into an AC socket properly configured for your particular
model.
4. Monitor Out
These two parallel speaker output jacks accept
standard 1/4
＂
two-conductor phone plugs, providing
300 watts of power at 4 ohms, or 200 watts at 8
ohms. Load impedances less than 2 Ohms will not
draw additional power and may cause the unit to go
into protect mode. The SPEAKERS MONITOR A and B jacks
are internally connected in parallel, and output the same
signals.
You can connect speakers with an impedance of 4-8ohm to
either or both the A or B jacks. You can connect speakers with
an impedance of 8-16ohm to both pairs.
NOTE :
Do not connect any devices other than speakers to
these jacks. Do not confuse these jacks with the MONITOR
jacks on the I/O panel.
5. Right Out
These two parallel speaker output jacks accept standard 1/4
＂
two-conductor phone plugs, providing 300 watts of power at
4 ohms, or 200watts at 8ohms.
Load impedances less than 4 ohms will not draw additional
power and may cause the unit to go into protect mode.
6. L+R Bridge
These two parallel speaker output jacks accept standard 1/4
＂
two-conductor phone plugs, providing 600 watts of power at
4 ohms, or 400watts at 8ohms.
Load impedances less than 4 ohms will not draw additional
power and may cause the unit to go into protect mode.
7. Left Out
These two parallel speaker output jacks accept standard
1/4
＂
two-conductor phone plugs, providing 300 watts of
power at
4 ohms, or 200watts at 8 ohms. Load impedances less than
4 ohms will not draw additional power and may cause the unit
to go into protect mode.
8. VM8-DRV Power Amp output
These two parallel speaker output jacks accept standard
1/4
＂
two-conductor phone plugs, providing 300 watts of power
at 4 ohms, or 200watts at 8 ohms. Load impedances less than
4 ohms will not draw additional power and may cause the unit
to go into protect mode
.
■
When the Stereo/Bridge select switch is set
to STEREO (2-Channel connection)
L/R channel signals are routed from the ST(L,R) bus to the
SPEAKER L/R jacks. The SPEAKERS L A/B jacks are
internally
wired in parallel and output the same signals. You can connect
a pair of speakers with an impedance of 4-8ohm to either or
both the A or B pair of the SPEAKER L/R jacks(total of two
speakers). You can connect two pairs of speakers with an
impedance of 8-16ohm to both A and B pair or the SPEAKER
L/R jacks(total of four speakers).
This connection provides a maximum output of 300W +
300W.
NOTE:
Do not connect anything to the SPEAKERS L+R
BRIDGE jack when you are using this 2-channel connection.
■
When the Stereo/Bridge select switch is set
to L+R BRIDGE (BRIDGE connection)
L/R channel signals are mixed in the ST bus and routed to the
SPEAKERS L+R BRIDGE jack as a monaural signal. You can
connect only one speaker with an impedance of 8-16ohm to the
SPEAKERS L+R BRIDGE jack. This connection provides the
maximum output of 600W
.
NOTE
:
Do not connect anything to the SPEAKERS L/R jacks
if you use this BRIDGE connection.
Panel Descriptions
Summary of Contents for VM-8DRV
