13
1. Power Switch
This switch controls the AC mains power to your powered
mixer. Power is on when the switch is in the on(up) position
and is confirmed when the power LED indicator is
illuminated.
Note :
Before turning on or off the mixer. It is a good idea to
turn down the main master and monitor master controls.
2. FUSE
The fuse is located in the fuse holder. (See Section
Ⅷ
Specifications for the correct values.)
3. IEC Socket
This is where you connect the supplied AC line cord to
provide AC power to the all VM series powered mixer. Plug
the line cord into an AC socket properly configured for your
particular model.
4. Monitor Out
These two parallel speaker output jacks accept standard
1/4
＂
two-conductor phone plugs, providing 300 watts of
power at 4 ohms, or 200 watts at 8 ohms. Load impedances
less than 2 ohms will not
draw additional power and may cause the unit to go into
protect mode. The SPEAKERS MONITOR A and B jacks are
internally connected in parallel, and output the same signals.
You can connect speakers with an impedance of 4-8 ohm to
either or both the A or B jacks. You can connect speakers with
an impedance of 8-16 ohm to both pairs.
Note :
Do not connect any devices other than speakers to
these jacks. Do not confuse these jacks with the MONITOR
jacks on the I/O panel.
5. Right Out
These two parallel speaker output jacks accept standard 1/4
＂
two-conductor phone plugs, providing 300 watts of power at 4
ohms, or 200 watts at 8 ohms.
(VM-11S DRVH:450watts/4ohms, 280watts/8ohms)
Load impedances less than 4 ohms will not draw additional
power and may cause the unit to go into protect mode.
6. L+R Bridge
This speaker output jacks accept standard 1/4
＂
two-conductor
phone plugs, providing 600 watts of power at 8 ohms.
(VM-11S DRVH:900watts/8ohms)
Load impedances less than 8 ohms will not draw additional
power and may cause the unit to go into protect mode.
7. Left Out
These two parallel speaker output jacks accept standard
1/4
＂
two-conductor phone plugs, providing 300 watts of
power at 4 ohms, or 200 watts at 8 ohms. Load impedances
less than 4 ohms will not draw additional power and may
cause the unit to go into protect mode.
(VM-11S DRVH:450watts/4ohms, 280watts/8ohms)
8. VM8-DRV Power Amp output
These two parallel speaker output jacks accept standard
1/4
＂
two-conductor phone plugs, providing 300 watts of
power at 4 ohms, or 200 watts at 8 ohms. Load impedances
less than 4 ohms will not draw additional power and may
cause the unit to go into protect mode
.
■
When the Stereo/Bridge select switch is set
to STEREO (2-Channel connection)
L/R channel signals are routed from the ST(L,R) bus to the
SPEAKER L/R jacks. The SPEAKERS L A/B jacks are
internally wired in parallel and output the same signals. You
can connect a pair of speakers with an impedance of 4-8ohm
to either or both the A or B pair of the SPEAKER L/R
jacks(total of two speakers). You can connect two pairs of
speakers with an impedance of 8-16ohm to both A and B pair
or the SPEAKER L/R jacks(total of four speakers).
This connection provides a maximum output of 300W +
300W.(VM-11S DRVH:450W+450W)
Note:
Do not connect anything to the SPEAKERS L+R
BRIDGE jack when you are using this 2-channel connection.
■
When the Stereo/Bridge select switch is set
to L+R BRIDGE (BRIDGE connection)
L/R channel signals are mixed in the ST bus and routed to the
SPEAKERS L+R BRIDGE jack as a monaural signal. You can
connect only one speaker with an impedance of 8-16 ohm to
the SPEAKERS L+R BRIDGE jack. This connection provides
the maximum output of 600W.(VM-11S DRVH:900W/8ohms)
Note:
Do not connect anything to the SPEAKERS L/R jacks
if you use this BRIDGE connection.
Ⅳ Panel Descriptions
Rear Panel
Summary of Contents for VM-11S DRV
Page 21: ...Ⅷ Block Diagram VM 11TDRV 21 ...
Page 22: ......