Stiroplus SP1045, Instructions For Use Manual

Page: 16 / 21

15
phenomenon will continue for several seconds. This is normal.
3. The appliance will shut off automatically if all the indicators blink five times together with five beeps can be heard
after being powered on, at that time, please contact the after-sales service department.
USING YOUR STEAM STATION
The appliance has two ironing ways. You can use dry ironing or steam ironing, the details refer to the following:
Dry ironing
1. Put the unit base on a stable and level surface and then put the iron on the thermal insulation stand of unit base.
2. Connect the plug to wall outlet and press down the power switch, the power indicator turns on.
3. Turn temperature dial to your desired setting, which is depended on the fabric of garment, and the temperature
indicator will illuminate. The iron starts heating. Refer to
“IRONING TIPS” and “ADDITIONAL TABLE” as below when
select temperature.
4. When the temperature indicator turns off, the selected temperature is reached. You can start ironing now.
WARNING: Never touch hot soleplate at any time before cooling down!
Steam ironing
The machine works with normal tap water. In case of very hard water (hardness above 27ºF) we suggest using 50%
distilled water diluted with tap water. Alternatively, we suggest using normal bottled drinking water. The use of de-
ionized water is not recommended.
1. Put the unit base on a stable and level surface.
2.Grasp the water tank’s handle to remove the water tank, then fill it with water through the filling aperture. You had
better use purified water with less calcium particles. After it, replace the water tank properly. The max capacity of
water tank is 1.7L, the water level shall not be exceeded the MAX mark.
3. Put the iron on the thermal insulation stand of unit base.
4. Connect plug to the wall outlet, press down the power switch, and the defaulted low steam rate indicator will
flash. And there are three modes including low, medium and high steam rate available, you can select the desired
steam rate for each garment according to your requirement. Make sure that there is enough water in the tank.
5. Turn temperature dial to your desired setting, which is depended on the fabric of garment, and the temperature
indicator will illuminate. The iron starts heating. Refer to
“IRONING TIPS” and “ADDITIONAL TABLE” as below when
select temperature.
6. The water in the steam generator will be heated, after a few minutes, the temperature indicator will extinguish, it
indicates the soleplate temperature has achieved the selected temperature. When the indicator of defaulted steam
rate changes from flashing to illuminating, it indicates that the iron is ready for ironing garment with steam.
7. Press the steam trigger with a little force, the steam will be sprayed from the soleplate continuously, and then you
can iron the garment with steam.
8. Quickly press the steam trigger twice to produce shot of steam if you need to remove hard crease. The “Shot of
steam” function can be only activated under medium steam rate and high steam rate.
Note: There may be dripping water during spraying steam when the temperature is at and lower than the second
setting. This is normal.
Caution: 1) Do not touch hot soleplate at any time before cooling down!
2) Never direct the steam at people!
3) Do not activate the steam trigger when the iron is placed on the unit base to avoid being scalded by
steam.
9. After ironing, press down the power switch for about 2 seconds, the appliance will be turned off and all the
indicators will extinguish. R emove the plug from the wall socket. But the soleplate is still hot, never touch it with
hand, place it on the thermal insulation stand until it cools down completely.
CLEANING AND MAINTENANCE
Before cleaning, first disconnect the power outlet and let the appliance cool down.
Wipe flakes and any other deposits on the soleplate with a damp cloth or a non-abrasive (liquid) cleaner.
NOTE: Do not use chemical, steel, wooden or abrasive cleaners to scrape the soleplate.
Clean the upper part of iron with a soft damp cloth. Wipe the water drop on the unit base and the thermal insulation
stand with a dry cloth.