Stihl TS 500i Service Manual Download Page 85

Page: 85 / 118

TS 500i

Screw in the screw (1) and
tighten it

– Fit the muffler,

6.1

9.2

Antivibration spring in
the support

The antivibration spring is located
between support and crankcase
and must be replaced if defective.

– Remove the support,

9.6

Unscrew screw (1) and remove
antivibration spring (2)

– Examine the antivibration spring

and replace it if necessary

1307RA034 TG

1307RA323 TG

Installation

Push antivibration spring (1) as
far as possible into the mount
(arrow ) and hold it in position
– antivibration spring is secured
against twisting

Screw in the screw (1) and
tighten it

– Install the support,

9.6

1307RA324 TG

1307RA325 TG

9.3

Antivibration spring at
the bottom of the
crankcase

The antivibration spring is secured
underneath the machine and must
be replaced if defective.

Remove screw (1)

– Remove front handlebar,

9.5

Pull the antivibration spring (1)
out of the handlebar

– Examine the antivibration spring

and replace it if necessary

1307RA326 TG

370RA262 TG

Summary of Contents for TS 500i























































































































Search results

Summary of Contents for TS 500i

Reviews:

Related manuals for TS 500i

Brands by name

Popular brands

Stihl TS 500i, Service Manual

Search results

Summary of Contents for TS 500i

Reviews:

Related manuals for TS 500i

Brands by name

Popular brands