manualshive.com logo in svg

Stihl SP 81, Instruction Manual

Share
Download
Stihl SP 81 Instruction Manual Download Page 15

14

English

SP 81

:

Apply a mark (with pencil or crayon) 
at distance 

A

 (40 mm) from the end 

of the drive tube.

:

Push the gearhead (

2

) onto the 

drive tube (

3

) – turn it back and forth 

at the same time – until it reaches or 
covers the mark on the drive tube.
Alternative check: The drive tube is 
correctly positioned when it 
completely closes the slot in the 
gearhead’s clamp (

see arrows

).

:

Line up the rakes parallel to the 
machine support or level with the 
ground.

:

Tighten down the clamp screws on 
the gearhead.

:

Move the handle hose (

4

) to the 

most comfortable working position.

A properly adjusted throttle cable is 
the precondition for correct 
operation in the full throttle, starting 
throttle and idle positions.

Adjust the throttle cable only after 
the unit is fully assembled

:

Use a suitable tool to push the slide 
to the bottom of the slot 

413BA015 KN

A

2

413BA016 KN

3

413BA017 KN

Adjusting the Throttle Cable

002BA163 KN

Summary of Contents for SP 81







































Reviews:

No comments

Brands by name

Popular brands

Load more brands