Stihl MSA 220 TC-O, Instruction Manual, Page: 53 / 408

– Data connection: Bluetooth
®
5.1. The
mobile appliance must be compatible with
Bluetooth
® Low Energy 5.0 and support
Generic Access Profile (GAP).
–
Frequency band: ISM band 2.4 GHz
–
Maximum RF power transmitted: 1 mW
–
Signal range: approx. 10 m. The signal
strength depends on the ambient conditions
and the mobile terminal. Signal range can
vary greatly depending on local conditions,
including the receiver. The range may be
perceptibly reduced inside enclosed rooms
and through metal barriers (such as walls,
shelves or cases).
–
Mobile appliance operating system require‐
ments: Android or iOS (current version or
higher)
21.5 Sound Values and Vibration
Values
STIHL recommends wearing ear defenders.
–
Sound pressure level L
pA
measured according
to EN ISO 22868: 94 dB(A) The K value for
the sound pressure level is 2 dB(A).
–
Sound power level L
wA
measured according to
EN ISO 22868: 104 dB(A) K-value (uncer‐
tainty) for sound power level is 2 dB(A).
–
Vibration level a
hv
measured according to EN
ISO 22867
–
Control handle: 3.4 m/s². The K value for
the vibration level is 2 m/s².
–
Handlebar: 3.0 m/s². The K value for the
vibration level is 2 m/s².
The sound and vibration levels indicated were
measured according to a standardized test
method and can be used as a basis for compar‐
ing electric power tools. The sound and vibration
levels actually occurring may vary from the val‐
ues indicated, depending on the type of applica‐
tion. The sound and vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual sound and vibration stress has
to be estimated. The times when the electric
power tool is switched off and the times when it
is switched on but running under no load can be
taken into account in the estimate.
21.6 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
22 Bar and Chain Combinations
22.1 STIHL MSA 220.0 T, MSA 220.0 TC Chainsaw
Pitch Drive link
gauge/groove
width
Length Guide bar Number of
teeth, spro‐
cket nose
Number of
drive links
Saw chain
3/8" P 1.3 mm
30 cm Rollomatic E /
Light 04
Rolloma‐
tic E Light /
Light P04
9
44
63 PM3 (3636)
63 PS3 (3616)
35 cm
1) 50
40 cm
1) 55
The cutting length of a guide bar depends on the chainsaw and the saw chain being used. The actual
cutting length of a guide bar may be less than the specified length.
1)
If this guide bar is used, the chainsaw may be used only with a STIHL AP battery inserted directly in
the saw.
23 Spare Parts and Accesso‐
ries
23.1 Spare parts and accessories
These symbols indicate original STIHL
spare parts and original STIHL acces‐
sories.
STIHL recommends the use of original STIHL
spare parts and accessories.
Despite ongoing market observation, STIHL is
unable to judge the reliability, safety and suitabil‐
ity of other manufacturers' spare parts and
accessories; accordingly, STIHL cannot warrant
for the use of those parts.
Original STIHL spare parts and original STIHL
accessories are available from STIHL dealers.
22 Bar and Chain Combinations English
0458-007-9801-A 53