manualshive.com logo in svg

Stihl MS 400 C-M, Instruction Manual

Share
Download
Stihl MS 400 C-M Instruction Manual Download Page 24

► Rotate the shroud fasteners (1) clockwise until

you hear a click.

The shroud fasteners (1) are locked.

► Fit the chain sprocket cover.

15.2

Cleaning the Bar and Chain

► Shut off the engine and engage the chain

brake.

► Remove the bar and chain.

1

2

0000-GXX-2951-A0

3

3

► Clean the oil port (1), oil inlet hole (2) and bar

groove (3) with a soft brush or STIHL resin

solvent.

► Clean the saw chain with a soft brush or

STIHL resin solvent.

► Mount the bar and chain.

15.3

Cleaning the Air Filter

Very fine dust can collect in the air filter. The

dust can clog the filter and cannot be removed

by brushing or knocking out. The air filter must

be cleaned with a cleaning agent.

► Shut off the engine and engage the chain

brake.

0000-GXX-7211-A0

1

1

3

► Rotate the shroud fasteners (1) a quarter turn

counterclockwise.

► Remove the shroud (2).

► Clean the area around the air filter (3) with a

damp cloth or a soft brush.

► Rotate the air filter (3) a quarter turn counter‐

clockwise by hand.

► Remove the air filter (3).

► Rinse away coarse dirt from the outside of the

filter (3) under running water.

► If the filter (3) is damaged. Install a new filter

(3).

WARNING

■ Cleaning agent may cause irritation if it con‐

tacts the skin or eyes.

► Observe the information supplied with the

cleaning agent.

► Avoid contact with cleaning agents.

► In case of contact with the skin: Wash

affected areas with plenty of water and

soap.

► In case of contact with the eyes: Rinse eyes

with plenty of water for at least 15 minutes

and seek medical advice.

► Spray the outside and inside of the air filter

(3) with STIHL special cleaner or a cleaning

agent with a pH value higher than 12.

► Allow STIHL special cleaner or cleaning agent

to act for 10 minutes.

► Use a soft brush to clean the outside of the air

filter (3).

► Rinse the outside and inside of the air filter (3)

under running water.

► Allow filter (3) to dry in the air.

0000-GXX-7212-A0

3

► Push the air filter (3) into place by hand and

rotate it clockwise until it engages in position.

The “STIHL” logo is horizontal.

► Place the shroud (2) in position.

► Rotate the shroud fasteners (1) clockwise until

you hear a click.

The shroud fasteners (1) are locked.

15.4

Cleaning the Spark Plug

► Shut off the engine and engage the chain

brake.

► Allow chainsaw to cool down.

3

0000-GXX-7213-A0

1

1

English

15 Cleaning

24

0458-788-0121-B

Summary of Contents for MS 400 C-M

































Reviews:

No comments

Brands by name

Popular brands

Load more brands