background image

1

0000-GXX-7209-A0

The oil feed rate is suitable for most applications

when the oil pump adjusting screw (1) is in posi‐

tion E (Ematic).
The oil pump feed rate can be adjusted to suit

different bar lengths, wood species and working

techniques.
To increase oil feed rate

► Shut off the engine and engage the chain

brake.

► Turn the oil pump adjusting screw (1) clock‐

wise.

To reduce oil feed rate

► Shut off the engine and engage the chain

brake.

► Turn the oil pump adjusting screw (1) counter‐

clockwise.

11.5

Holding and Controlling the

Chainsaw

0000-GXX-2948-A1

► Hold and control your chainsaw with your left

hand on the handlebar and your right hand on

the control handle. Wrap thumb of left hand

around the handlebar and thumb of right hand

around the control handle.

11.6

Sawing

WARNING

■ If kickback occurs, the chainsaw can be

thrown up in the direction of the operator. This

may result in serious or fatal injury to the user.

► Always cut with the chain running at full

speed.

► Do not cut with the upper quadrant of the

guide bar nose.

► Begin the cut with the chain running at full

speed and keep the guide bar vertical.

0000-GXX-2949-A1

► Engage the spiked bumper and use it as a ful‐

crum.

► Guide the full width of the guide bar into the

wood and reposition the spiked bumper as

required.

► Take the weight of the chainsaw at the end of

the cut.

11.7

Limbing

0000-GXX-2950-A1

► Support the chainsaw on the log.

► With the chain running a full speed, pivot the

guide bar downward against the limb.

► Cut through the limb with the top of the guide

bar.

11 Operating the Saw

English

0458-788-0121-B

19

Summary of Contents for MS 400 C-M

































Reviews: