background image

29

HTE 60

English

Sharpening tools

Filing gauge

Flat file

File holder with round file

Round file

Gauge

Reference gauge for chain sprocket

Other special accessories

Safety glasses

Harness

Combination wrench

STIHL lubricating grease

Angle drive

3/8"P-7T spur sprocket

Contact your STIHL dealer for the latest 
information on these and other special 
accessories.

Users of this machine may only carry 
out the maintenance and service work 
described in this user manual. 
All other repairs must be carried out 
by a servicing dealer.

STIHL recommends that all 
maintenance and repair work be carried 
out by an authorized STIHL dealer. 
STIHL dealers regularly attend training 
courses and are supplied with the 
necessary technical information.

When repairing the machine, only use 
replacement parts which have been 
approved by STIHL for this power tool 
or are technically equivalent. Only use 
high-quality replacement parts in order 
to avoid the risk of accidents or damage 
to the machine.

STIHL recommends the use of genuine 
STIHL replacement parts.

Original STlHL parts can be identified by 
the STIHL part number, the 

STIHl

 

logo and the STlHL parts symbol 

(

The symbol may appear alone on small 
parts.

Electrical appliances must not be thrown 
in the garbage can. Take the unit, 
accessories and packaging to an 
approved disposal site for environment-
friendly recycling.

Special Accessories

Maintenance and Repairs

Disposal

Summary of Contents for HTE 60

































Reviews: