background image

FS 87, FS 87 R

English

2

Pictograms

The meanings of the pictograms 

attached to the machine are explained in 

this manual.
Depending on the model concerned, the 

following pictograms may be attached to 

your machine.

Symbols in text

Warning where there is a risk of an 

accident or personal injury or serious 

damage to property.

Caution where there is a risk of 

damaging the machine or its individual 

components.

Engineering improvements

STIHL's philosophy is to continually 

improve all of its products. For this 

reason we may modify the design, 

engineering and appearance of our 

products periodically.
Therefore, some changes, modifications 

and improvements may not be covered 

in this manual.

Observe all application local safety 

regulations, standards and ordinances.
If you have not used this type of power 

tool before: Have your dealer or other 

experienced user show you how to 

operate your power tool or attend a 

special course in its operation.
Minors should never be allowed to use a 

power tool.
Keep bystanders, especially children, 

and animals away from the work area.
When the power tool is not in use, shut it 

off so that it does not endanger others. 

Secure it against unauthorized use.
The user is responsible for avoiding 

injury to third parties or damage to their 

property.

Guide to Using this Manual

Fuel tank; fuel mixture of 

gasoline and engine oil

Operate decompression 

valve

Manual fuel pump

Operate manual fuel 

pump

Tube of grease

Intake air: Summer 

operation

Intake air: Winter 

operation

Handle heating

Safety Precautions and 

Working Techniques

Some special safety pre

-

cautions must be 

observed to reduce the 

risk of personal injury 

when operating this 

power tool because of the 

very high speed of its cut

-

ting attachment. 
It is important you read 

and understand the 

instruction manual before 

first use and keep the 

manual in a safe place for 

future reference. Non-

observance of the 

instruction manual may 

result in serious or even 

fatal injury.

Summary of Contents for FS 87

















































Reviews: