background image

18.3

Standard Setting

► Shut off the engine.

0000-GXX-2946-A0

H

L

► Turn the high speed screw (H) counterclock‐

wise as far as stop.

► Turn the low speed screw (L) clockwise as far

as stop.

► Turn the low speed screw (L) 3/4 of a turn

counterclockwise.

18.4

Adjusting Idle Speed

► Carry out the standard setting.

► Start the engine.

► Warm up the engine by opening and closing

the throttle for about 1 minute.

0000-GXX-4782-A0

Engine stops while idling

► Turn the idle speed screw (LA) clockwise until

the cutting attachment begins to rotate.

► Turn the idle speed screw (LA) one full turn

counterclockwise.

Erratic idling behavior or poor acceleration

► Turn the low speed screw (L) clockwise or

counterclockwise until the engine runs and

accelerates smoothly.

Cutting attachment rotates when engine is idling

► Turn the idle speed screw (LA) counterclock‐

wise until the cutting attachment stops rotat‐

ing.

► Turn the idle speed screw (LA) one full turn

counterclockwise.

18.5

Clearing the Combustion

Chamber

2

3

1

0000-GXX-4736-A0 

► Pull off the spark plug boot (1).

► Unscrew the spark plug (2).

► Dry the spark plug (2).

WARNING

■ Unconfined sparks may occur if the starter grip

is pulled after the spark plug boot has been

removed. Sparks may cause a fire or an

explosion in an easily combustible or explo‐

sive environment. This can result in serious or

fatal injuries and damage to property.

► Move the slide control to position 

before pulling the starter grip.

► Move the slide control to position .

► Pull the starter grip (3) several times and

guide it back slowly.

The combustion chamber is cleared.

► Insert and tighten down the spark plug (2)

firmly.

► Connect the spark plug boot (1) and press it

down firmly.

19 Specifications

19.1

STIHL FR 235 Trimmer

Displacement: 36.3 cc

Engine power to ISO 8893: 1.55 kW (2.1 bhp)

at 9,000 rpm

Idle speed: 2,800 rpm

Max. output shaft speed: 7,900 rpm

Approved spark plug: Bosch WSR 6 F from

STIHL

Electrode gap: 0.5 mm

Dry weight without cutting attachment and

deflector: 10.3 kg

Length without cutting attachment: 2750 mm

Max. fuel tank capacity: 810 cc (0.81 l)

19 Specifications

English

0458-527-0121-B

21

Summary of Contents for FR 235

























Reviews: